Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
. . . . . . . . . . . . . . . . 4100040300RP 10. Upper Light Harness. . . . . . . . . . . . . . . 4200120400RP 11. Mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . 5900060600RP 12. Reflector Assembly. . . . . . . . . . . . . . . . 5900080600RP 13. Front Glass. . . . . . . . . . . . . . . . . . . . . . 5900440100RP 14. Capacitor . . . . . . . . . . . . . . . . . . . . . . . .2300030100RP 15. Terminal Block . . . . . . . . . . . . . . . . . . . .4000070100RP 16. Control Knob . . . . . . . . . . . . . . . . . . . . .8800000300RP 17. Remote Control Receiver. . . . . . . . . . . 3000380100RP 18. Remote Control Transmitter . . . . . . . . . 3000370500RP 19. LED Log Driver (DS7425DLX) . . . . . . . 3000390100RP 6 1 2 3 4 5 9 10 8 7 13 12 11 14 18 15 16 17 7 Wiring Diagram DS7420 MOD A - D TO REPLACE UPPER LIgHT BULB • WARNINg: If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. • WARNINg: Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There is one bulb at the top of the opening that illuminates the log set exterior and two bulbs under the log set which generate the flames and embers. It is a good idea to replace all of the light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace the light bulbs. 1. Open door by pulling the handle. 2. Locate the upper bulb bracket. 3. Bend light retainer bracket down. 4. Locate and remove the light bulb. 5. Insert new bulb. 6. Bend light retainer bracket back into its original position. 7. Close the door. UPPER LIgHT BULB REQUIREMENTS: Quantity of 1 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 7 watt rating. TO REPLACE LOWER LIgHT BULBS • WARNINg:If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. • WARNINg:Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There is one bulb at the top of the opening that illuminates the log set exterior and three bulbs under the log set which generate the flames and embers. It is a good idea to replace all of the light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace the light bulbs. 1. Remove the stove pipe kit (if equipped). 2. Gently place stove on its back on a flat surface. 3. Remove the heater cover retaining screws located on the bottom of the stove and lower heater and light assembly out onto the floor. 4. Remove the burnt out bulb(s) by pulling straight out of socket. If bulbs are difficult to remove form socket move the bulb from side to side while pulling being careful not to damage the light socket. 5. Replace the lower light bulbs. 6. Reassemble in the reverse order as above. LOWER LIgHT BULB REQUIREMENTS: Quantity of 3 – 35 watt Halogen Quartz lamps, 120 volt, G9 base. DO NOT ExCEED 35 WATTS PER BULB TO REPLACE MAIN POWER SWITCH • WARNINg: If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. • WARNINg: Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. 1. Remove back panel screws located along the rear of the top panel. 2. Open front door and release the Cams located in the upper corner of both side panels. ! NOTE: To release Cams ensure arrow on Cam is facing up. arrow 3. Remove top panel. 4. Locate the main on/off switch mounted on the rear panel and disconnect the wiring clips and connections noting their original locations. 5. Depress the retainer clips on the rear of the switch and push the switch out of the rear cover. 6. Properly orient the new switch and connect all of the wiring clips and connections. 7. Reassemble in the reverse order as above. TO REPLACE UPPER LIgHT ON/OFF SWITCH • WARNINg: If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. • WARNINg: Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. 1. Remove back panel screws located along the rear of the top panel. 2. Open front door and release the Cams located in the upper corner of both side panels. ! NOTE: To release Cams ensure arrow on Cam is facing up. arrow www.dimplex.co...
Dieses Handbuch ist für folgende Modelle:Standbacköfen - DS7425DLX (1.29 mb)