Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
About Cassette tape • If the tape is slack tighten it. • If the cassette tape label is peeling off glue it on again. • Don’t use deformed cassette tape. • Don’t place cassette tape on the dashboard etc. where the temperature is high. • Don’t use cassette tape that’s 100 minutes long or longer. — 4— General features Power SRC/ PWR OFF . 4CLK FM AMAUD/ A.ADJ ATT/ LOUD d u #1 - 5 ATT indicator Clock indicator Clock display Release button LOUD indicator Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [PWR OFF] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUnE" Tape "TAPE" Standby (Illumination only mode) "OFF" — 5— General features English Volume Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. Loudness Compensating for low and high tones during low Press the [LOUD] button for at least 1 second. Each time the button is pressed for at least 1 second Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. dB (Sound Coordinate) You can recall the best sound the music. 1 Select the source Press the [SRC] 2 Enter Control mode Press the [AUD] button. 3 Select the Sound type Press the [#1] — [#5] button. Press button Sound setting Display [#1] Flat "DB-1" [#2] Rock "DB-2" [#3] Pops "DB-3" [#4] Jazz "DB-4" [#5] Easy "DB-5" When the dB(Sound Coordinate) setting is changed, the Bass and Treble set in audio control replace the dB(Sound Coordinate) values. 4 Exit Control mode Press the [AUD] button. Audio Control 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [A.ADJ] button for at least 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. — 6— Adjustment Item Bass level Treble level Balance Display "BAS" "TRE" "BL" Range –4 — 4 –4 — 4 Left 15 — Right 15 The faceplate of the unit can be detached and taken with you, helping to deter theft. Fader "FD" Rear 15 — Front 15 Removing the Faceplate Theft Deterrent Faceplate 5 Exit Audio Control mode Press the [A.ADJ] button. Switching Clock Display Switching the displayed information. Press the [CLK] button. Each time the button is pressed it switches between clock display and current source. During clock display the clock indicator is ON. Adjusting Clock 1 Select the clock display Press the [CLK] button. 2 Enter clock adjustment mode Press the [CLK] button for at least The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment Press the Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate 1 Align the projections on the unit with the grooves on the faceplate. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing — 7— English Tuner features Tuning Mode AUTO/ AME FM/ SRC . 4 CRSC AM#1 - 6 STEREO indicator Frequency display Preset station number AUTO indicator Band display (CRSC) indicator Choose the tuning mode. Press the [AUTO] button. Each time the button is pressed the Tuning mode switches as shown below. Tuning mode Display Operation Auto seek "AUTO" Automatic search for a station. indicator Manual — Normal manual tuning control. Tuning Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display. 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it FM1, FM2, and FM3 bands. 3 Tune up or down band Press the [ 4] or [ . ] button. During reception of stereo stations — 8— Station Preset Memory Putting the station in the memory. 1 Select the band Press the [FM] or [AM] button. 2 Select the frequency to put in the memory Press the [ 4] or [ . ] button. 3 Put the frequency in the memory Press the [#1] — [#6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [#1] — [#6] button. Auto Memory Entry Putting stations with good reception in the memory automatically. 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button. 2 Open Auto Memory Entry Press the [AME] button for at least 2 seconds. When 6 stations that can be received Auto Memory Entry closes. 2 Call up the station Press the [#1] — [#6] button. CRSC (Clean Reception System Circuit) Temporarily have...
Dieses Handbuch ist für folgende Modelle:Player - KRC-21SG (648.1 kb)