Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Fotos und technische Daten Sony D-NE10 |
Anleitung Zusammenfassung
• Use the AC power adaptor for recording. If you use the rechargeable battery or dry battery as a power source, the battery may become completely depleted during recording. • Adjust the volume properly on the connected device so that the sound will not be distorted. • This CD player uses the Serial Copy Management System, which allows only first- generation digital copies to be made. • When recording or playing an ATRAC CD/MP3 CD using a connected device, use only the analog connecting cord. • If you change the connected device, make sure to change the “AUDIO OUT” setting. MiniDisc recorder, DAT deck, etc. When the headphones or other devices are connected to the i/LINE OUT (OPTICAL) jack When an optical digital connecting cord is connected, the output is automatically switched to an optical digital output. When a remote control or a connecting cord is connected: The current AUDIO OUT setting (“HP” or “LINE”) flashes for about 5 seconds. If you connect another device to the i/LINE OUT (OPTICAL) jack, first remove the device and connect the headphones again, then switch the AUDIO OUT setting to “HP.” When AUDIO OUT is set to “LINE” You cannot adjust the volume using VOL +/– on the CD player or the remote control. When using an optical digital connecting cord To record a CD on a MiniDisc, DAT, etc., make sure that the CD player is paused before starting the recording procedures. About the G-PROTECTION and equalizer functions when using the connecting cord or the optical digital connecting cord •To record high quality CD sound, set the G-PROTECTION setting to “G-PRO 1” on the menu. • If the AUDIO OUT setting is set to “LINE,” the parametric equalizer function does not work. Connecting your CD player 27 B Connecting to a power source You can check the remaining power of the battery in the display. t t t t t Lobatt* * Beep sounds. When the battery is depleted, charge the rechargeable battery or replace the dry battery with new one. • Using the rechargeable battery (this page) • Using the dry battery (page 30) Notes • The indicator sections of roughly show the remaining battery power. One section does not always indicate one-fourth of the battery power. • Depending on operating conditions, the indicator sections of may increase or decrease. • When using the rechargeable battery and dry battery together to extend power, use a fully charged rechargeable battery and new dry battery. For the battery life and charging time of the rechargeable battery, see “Specifications.” Using the rechargeable battery Charge the rechargeable battery before using it for the first time. To keep the original battery capacity for a long time, charge the battery only when it is completely depleted. You can use only the following rechargeable battery for your CD player. • NH-14WM (supplied) 1 Squeeze OPEN from both sides to open the lid of your CD player, then open the battery compartment lid inside the player. 12 2 Insert the rechargeable battery by matching the 3 to the diagram in the battery compartment and close the lid until it clicks into place. Insert the # end first. 3 Connect the AC power adaptor to the DC IN 3 V jack of the supplied charging stand and an AC outlet. Then place the CD player on the supplied charging stand (page 14). Charging of the battery starts. In the display of the remote control, “Charging” indication flashes and the indicator sections of light up in succession. The OPERATION lamp lights up on the CD player. When the battery is completely charged, all indications on the display disappear and the OPERATION lamp goes off. OPERATION lamp to DC IN 3V on the charging stand AC power adaptor to an AC outlet Notes on the supplied charging stand • The supplied charging stand can be used only with this CD player. No other model can be charged using this stand. • When using the supplied charging stand, charge the rechargeable battery only. Do not charge any other battery. • During charging, the CD player and the rechargeable battery become hot. This poses no danger. • Do not place coins or other metallic objects on the charging stand. If the terminal on the charging stand is accidentally brought into contact with a metallic object, it may short-circuit and begin to heat up. To charge the rechargeable battery without using the supplied charging stand 1 Perform steps 1 and 2 of “Using the dry battery” (page 30) to attach the external battery case to the CD player. 2 While keeping sliding the switch on the external battery case in the direction of the arrow, connect the AC power adaptor. 3 Press x/CHG. Charging starts. OPERATION lamp AC power adaptor DC IN 3 V x/CHG Connecting to a power source to an AC outlet (Continued) 29 Using the rechargeable battery Notes • During charging, the CD player and the rechargeable battery become hot. This poses no danger. • If you press u during charging, charging stops and playback of the CD starts. • If you place the CD player on the charging stand during play, play stops and charging st...