Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• The terminals of the battery charging stand is dirty. , Clean the terminals with a dry cloth (page 65). Battery charging stand and the recorder become hot during the charging procedure. • This is not a trouble and poses no danger. While recording Symptom Cause/Remedy The recorder overwrites existing materials when record. • The record starting-position setting (“REC-Posi”) is set to “From Here”. , Set “REC-Posi” setting to “From End”. The recording starts from the end of the disc even when “REC-Posi” is set to “From Here”. • The group recording (“ : REC”) is set to “ : REC ON”. (You cannot overwrite tracks when “ : REC” is set to “ : REC ON”.) , Set the group recording setting to “ : REC OFF” (page 53). “REC-Posi” (the record-starting point) cannot be set to “From Here”. • The group recording (“ : REC”) is set to “ : REC ON”. , Set the group recording setting to “ : REC OFF” (page 53), and then set “REC-Posi” to “From Here”. continued Symptom Cause/Remedy Recording cannot be done correctly. • Audio sources may not be securely connected. , Disconnect the audio sources once and connect them again (pages 17, 18, 21). • There is no digital signal from the portable CD player. , When recording digitally from a portable CD player, use the AC power adaptor and disable the anti-skip function (such as ESP) on the CD player (page 21). • The analog recording was made using a connecting cord with an attenuator. , Use a connecting cord without an attenuator. • Recording level is too small to record (when adjusting the recording level manually). , Pause the recorder and adjust the recording level (page 31). • The power sources was disconnected or a power outage occurred during recording. , The recording result is not recorded on the disc. Make recording again. • The premastered MD is inserted. , Replace to the recordable MD. • The remaining recordable time on the disc is 12 seconds or less (“DISC FULL” appears). , Replace the disc. Recording stops • You tried to overwrite a track which is checked out from the automatically while computer. (Tracks that are checked out from the computer recording. cannot be overwrite. The recording stops automatically.) , Check back the checked out track into the computer. , Record from the end of the disc. Stereo sound is heard • This is normal. During digital recording, the sound will be stereo in the headphones/ in the headphones/earphones, even though the recorded sound is earphones while monaural. recording in monaural. Momentary noise is • Due to the special digital audio compression technology used in heard when LP4 stereo mode, momentary noise may occur on very rare recording. occasions with certain sound sources. , Record in SP or LP2 mode. The lid does not open after recording. • The lid does not open until “TOC Edit” disappears in the display. Symptom Cause/Remedy “TR FULL” appears even before the disc has reached the maximum recording time (60, 74, or 80 minutes) and the recording cannot be done. • This is due to the MiniDisc system limitation. When 254 tracks have been recorded on the disc, “TR FULL” appears regardless of the total recorded time. More than 254 tracks cannot be recorded on the disc. , To continue recording, erase unnecessary tracks. The remaining recording time does not increase even after erasing numerous short tracks. • This is due to the MiniDisc system limitation. Tracks of under 12 seconds (in SP stereo), 24 seconds (in LP2 stereo mode or monaural), or 48 seconds (in LP4 stereo mode) in length are not counted and so erasing them may not lead to an increase in the recording time. While playing Symptom Cause/Remedy An MD is not played normally. • Repeat play is selected. , Use MENU on the recorder or press P MODE/ on the remote control to change back to the normal play. • Playback mode is changed. , Use MENU on the recorder or press P MODE/ on the remote control to change back to the normal play. An MD is not played from the first track. • Disc playing stopped before it came to the last track. , Press N for 2 seconds or more to start playing, or press the control towards . repeatedly on the remote. Playback sound • The recorder is placed where it receives continuous vibration. skips. , Put the recorder on a stable place. • A very short track may cause sound to skip. , Try not to create a track under one second long. Sound has a lot of static. • Strong magnetism from a television or such device is interfering with operation. , Move the recorder away from the source of strong magnetism. The volume of the recorded track is low. • The track was recorded in analog (When recorded in digital, the recording level will be automatically adjusted as same as the sound source), or you used a connecting cord with an attenuator. , Use a correct connecting cord. • The recording level was low. , Adjust the recording level manually when recording. Volume cannot be turned up. •AVLS is on. , Release AVLS settings (page 57). Symptom Cause/Remedy No sound comes • The headphones/...