Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
The batteries will last longer when the ESP function is turned off. Notes: • The music may stop if the player receives continuous shocking • You may hear noise or skipping if the CD is dirty or scratched. 13 • If during ESP play, you press Pause, or Search buttons, the memory basket will empty itself temporarily. 8. Repeat play a) Repeat play-single track Plays one song over and over till you press Stop. During play press the P-Mode Button once the symbol REPEAT is display. The song currently playing will repeat over and over until you press stop To stop repeat play, press the "P-Mode" four times till the word REPEAT disappears. b) Repeat play-all tracks Repeats all songs in order till you press stop. During play, press the P-Mode button twice, the symbol REPEAT ALL will show steady in the display. All songs will keep playing in the sequence 1,2,3 etc. and all songs will repeat and when finished, will start all over again until you press the stop button. To stop repeat play press the P-Mode button till the word REPAET ALL disappears. 14 9. Intro play This plays the first 10 seconds of all songs in sequential order: 1. During play, press the P-Mode Button till the word INTRO flash in the display 2. Press PLAY/PAUSE buttons, the word INTRO will stop flashing and the first 10 seconds of each song on the CD will play and then the set will stop. 3.When you find a song you like press Play, the word INTRO will go off and that song (all the following songs) will play NORMALLY. 10. Random play 1. During play, press P-Mode Button four times the word SHUFF will flash during play. 2. Press PLAY/PAUSE, this will play all of the songs in random order selected by the CD player. 3. Press the search button 11.Programming your playing Sequence programmed play The tracks on the disc can be programmed (arranged in advance) to play in any order you prefer (up to 20 tracks can be programmed). I , to skip to the next random song. 15 Programming example Program number 1 2 3 4 5 6 7 8 Track number 3 5 8 1 2 4 1 1 During programming, the word PROGRAM will flash in the display. To play in your preferred order, follow steps below: 1. Press the Program button. 2. Press the search button or ►Wto select track number, for example 3. 3. Press the program button. Track 3 is now programmed. 4. Repeal steps 2 and 3 to program other tracks till you finish (up 20 selections). 03:01 II 5. After programming is finished press Play to begin programmed play. PROGRAM stops flashing and music begins (the display still shows PROGRAM). fSoi-Notes: 03:02 II The player stops automatically after all programmed tracks have been played, or the CD Door is opened, or stop is pressed, or after power shuts off • Your programming will be lost: - if the CD door is opened. - when the alkaline batteries are exhausted is disconnected. - when you press stop. 16 Wired controller 1. Location of controls 1- play/pause 2- stop/of 3- search button (forward) 4- volume button - 5- hold button 6- search button (backward) 7- earphone jack 2. How to use Wired Controller Illustration for how to connect Wired Controller Note: The operation of the buttons on Wired Controller is as same as buttons on Panel of the player. 17 Handling compact discs • This set is desired to play only compact discs bearing this identification logo (logo must say DIGITAL AUDIO). Other discs may not conform to the CD standard and may not play properly. • Dirty, scratched or warped discs may cause skip ping or noise. • Handle the disc only by the edges. To keep clean do not touch its surface. • Discs should be stored in their cases after use to avoid scratches. • Do not expose discs to direct sunlight, high humidity, high temperature or dust. Prolonged exposure to extreme temperature can wrap the disc (such as leaving the discs in your car during summertime). • Do not stick or write anything on either side of disc. Sharp writing instruments, or the inks used in some felt-tip pens, may damage its surface. Cleaning 1. Cleaning the cabinet Wipe with a soft cloth. If the cabinet is very dampen (not dropping wet) the cloth with a weak solution of soapy water, and then wipe clean. 18 2. Cleaning the lens A dirty lens will cause sound skipping. If the lens is very dirty, the play work Open the CD door and clean the lens as follows: a) Dirty or dry particles on the lens. Using a camera lens brush/blower, blow on the lens a few times, then wipe it lightly with the brush to remove dust. Then, blow on the lens once more. b) Fingerprints on the lens If the lens does not get clean using brush-blower, use a cotton swab moistened with alcohol to gently c lean the lens and then dry with a soft cloth. 3. Cleaning discs Fingerprints should be carefully wiped from the surface of disc with a soft cloth. Unlike conventional records, compact discs have no grooves to collect dust and macroscopic dirt, so gently wiping them with a soft cloth sh...