Stimmen - 4, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: IBM Dateigröße: 12.51 mb Dateiname: Unterrichtssprache:

Two short beeps and a blank screen. 1. System board. 2. DIMM. Two or more beeps, or a continuous beep. Operating system starts successfully. If a mini-PCI Ethernet card is installed, confirm that Alert On LAN 2 in the ThinkPad Setup program is disabled. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2. System board. One short beep, pause, three short beeps, pause, three more short beeps, and one short beep. Only the cursor appears. Reinstall the operating system. Four cycles of four short beeps and a blank screen. System board (security chip) Five short beeps and a blank screen. System board 48 ThinkPad X220 Tablet and X220i Tablet Hardware Maintenance Manual No-beep symptoms Table 5. No-beep symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, and no POST. 1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST. 1. Reseat DIMM. 2. System board. The power-on password prompt appears. A power-on password or a supervisor password is set. Type the password and press Enter. The hard-disk password prompt appears. A hard-disk password is set. Type the password and press Enter. LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced. Notes: • This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later. • Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects. • One pixel consists of R, G, B sub-pixels. Table 6. LCD-related symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, and a blank LCD during POST. System board. • LCD backlight not working. • LCD too dark. • LCD brightness cannot be adjusted. • LCD contrast cannot be adjusted. 1. Reseat the LCD connectors. 2. LCD assembly. 3. System board. • LCD screen unreadable. • Characters missing pixels. • Screen abnormal. • Wrong color displayed. 1. See important note for “LCD-related symptoms.” 2. Reseat all LCD connectors. 3. LCD assembly. 4. System board. Horizontal or vertical lines displayed on LCD. LCD assembly. Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. Chapter 4. Related service information 49 2. If no error is detected, do not replace any FRUs. 3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no more errors exist. Undetermined problems If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed, or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects). Verify that all attached devices are supported by the computer. Verify that the power supply being used at the time of the failure is operating correctly. (See “Power system checkout” on page 33.) 1. Turn off the computer. 2. Visually check each FRU for damage. Replace any damaged FRU. 3. Remove or disconnect all of the following devices: a. Non-ThinkPad devices b. Devices attached to the docking station or the port replicator c. Printer, mouse, and other external devices d. Battery pack e. Hard disk drive f. External diskette drive or optical drive g. DIMM h. Optical disk or diskette in the internal drive i. PC Cards 4. Turn on the computer. 5. Determine whether the problem has been solved. 6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU): a. System board b. LCD assembly 50 ThinkPad X220 Tablet and X220i Tablet Hardware Maintenance Manual Chapter 5. Status indicators This chapter presents the system status indicators that show the status of the computer. 56 © Copyright Lenovo 2011 Table 7. Status indicators Indicator Meaning 1 Wireless LAN status Green: The wireless LAN feature is on, and the radio link is ready for use, or the data is being transmitted. Blinking green: Data is being transmitted (for some models). 2 Wireless s...

Herunterladen

Geben Sie zwei Ziffern: