Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2 GSR10Pub1000002369 6/14/05 4:57 PM Page 4 UNPACKING BOX CONTENTS Important: For warranty verification, please do not remove line cord sticker. After you unpack your unit, verify that you received the following parts (A): A 1. Telescopic pole 2. Lint brush attachment 3. Flexible hose 4. Unit with water tank 5. Trouser clamps holder assembly 6. Trouser clamps 7. Steam nozzle/hanger 3 GETTING FAMILIAR WITH YOUR UNIT B † 1. Steam nozzle holder (Part # GSR10-03) 2. Steam nozzle 3. Steam nozzle button † 4. Lint brush attachment (Part # GSR10-01) 5. Hanger holder 6. Clip for keeping hanger in place 7. Cord wrap 8. Telescopic pole † 9. Flexible hose (Part # GSR10-08) † 10. Trouser clamps (Part # GSR10-4 †11. Trouser clamps holder (Part # GSR10-05) † 12. Lock nut for telescopic pole (Part # GSR10-04) † 13. Removable water tank (Part # GSR10-06) † 14. Water tank cap (not shown) (Part # GSR10-07) † 15. Wheel casters (Part # GSR10-09) 16. Steam On/Off switch with indicator lights † Consumer replaceable GSR10Pub1000002369 6/14/05 4:57 PM Page 6 ASSEMBLING YOUR UNIT C D E F G H J Inserting Flexible Hose 1. To connect the flexible hose, align connector prongs with holes on the unit and push inside the connector (C). 2. Slide the lock nut through the hose all the way to the end. 3. Place lock nut over the unit connector and twist clockwise tightly in place (D). Inserting Trouser Clamps Holder Assembly For your convenience the trouser clamps can be used as a regular clip hanger at the top of the telescopic pole or to clip the bottoms of the pants. 1. Loosen the holder lock nut by turning it counterclockwise. 2. Find the slot at the bottom of the pole, insert and slide holder assembly with holder facing as shown (E). Note: If using the trouser clamps as a regular clip hanger, slide the holder assembly to the top of the pole. 3. Secure assembly in place by twisting the lock nut clockwise until it is tight (F). Tip: Make sure the trouser holder is in the upright position. 4. Insert and push trouser clamp bar securely into the holder. Inserting Telescopic Tube 1. With the trouser clamp holder in place, remove the lock nut from the unit connector by turning it counterclockwise (G). 2. Insert and slide the narrow end of the lock nut through the flat end of the telescopic pole (H). 3. Hold the telescopic pole and insert into the connector. a. Look inside the connector and find the alignment notch (b. Take the telescopic pole, align the open slot at the end the notch inside the connector and push the telescopic all the way inside the connector. You might have to wiggle it to fit in. Important: The slot on the telescopic pole must slide notch inside the connector for the pole 5 Steam NozzleTrousers KMRLNPQ or 4. Once the telescopic pole is inside the connector, twist the lock nut clockwise until tight (K). Inserting Steam Nozzle Holder Assembly 1. Pull up one extension tube at time and tighten each lock nut by twisting clockwise (L). 2. Insert steam nozzle holder assembly at the top of the telescopic pole and rotate it clockwise until securely in place (M). 1. Insert steam nozzle into its holder (N). 2. Attach the lint brush to the nozzle by inserting end tabs into the nozzle slots (P). Your unit is now assembled! How to Use This appliance is for household use only. GETTING STARTED Filling Water Tank 1. Make sure the unit is unplugged. 2. Place unit on the floor. 3. Grasp water tank handle and remove water tank. 4. Turn the water tank upside down and remove the cap by turning it counterclockwise (Q). 5. Fill the water tank with water. Important: Do not add cleaning solutions or any other chemicals to the water in the tank. Only use regular tap water. 6. Replace the cap and tighten by turning it clockwise. 7. Insert water tank back into the unit securely in place. STEAMING GARMENTS 1. Make sure the unit is Off. 2. Using a clip hanger, hang the pants by the waist on the hanger holder. 3. Stretch the pants and clip the bottoms clamps or move the trouser the pole and using the trouser the waist (R). Note: To steam other hanging hanger on the hanger 6 GSR10Pub1000002369 6/14/05 4:57 PM Page 8 S T 4. Plug in the unit into an electrical outlet. 5. Press the On/Off (I/0) switch (S). 6. Remove the steam nozzle from its holder facing upward, away from you and press the Steam button (T). The indicator lights on the unit illuminate and in a few seconds steam is released. Important: • Never place your hand in front of steam nozzle where steam is being released. • Do not leave the steam nozzle in one area for a long period of time because the garment will get wet. 7. Use the lint brush to remove lint from the fabric as it steams. Automatic Shutoff The unit shuts off automatically: • After 30 minutes of inactivity • If water tank is empty To use the unit again, turn Off then On and resume operation. Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. Cleaning 1. Make s...