Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
n o q p ASSEMBLY & USE INSTRUCTIONS 1 Safely remove contents of the Portable Steam Pocket® Cleaning System and lay them out on a flat surface to see that you have all the components to complete the assembly. 2 READ ALL INSTRUCTIONS BEFORE USING YOUR PORTABLE STEAM POCKET®. IMPORTANT: Always make sure the steam bottle is UNPLUGGED from the electrical outlet when not in use. Never fill the water reservoir when the unit is plugged in. FILLING AND REFILLING THE WATER TANK 1 Never fill the steam bottle while plugged into an electrical outlet. 2 Disconnect the power cord before filling the water tank. 3 Turn the water tank cap counter clockwise and remove to fill, using the filling flask provided. Be careful not to overfill. Replace the cap by turning clockwise. 3 Using Your Portable Steam Pocket® DIRECT SPRAY STEAM BOTTLE USE Cleaning Tip: Direct steam spray for cleaning hard to reach nooks & crannies and stubborn sticky messes where focused steam power may be needed. Direct steam spray can loosen and dislodge compact dirt often found in corners and tight places where traditional methods and cleaning tools tend to push dirt into, making it difficult to reach and clean. Spray direct steam and wipe clean with a cleaning cloth. CAUTION: Direct steam spray temperature is extremely hot closest to the nozzle and can damage surfaces if held directly focusing in one spot too long. Be sure to constantly move and adjust the steam spray to avoid causing damage. 1 3 4 1 Attach the hose connector. Aligning the arrow located on the hose connector with the un-lock symbol located on the nozzle connector. Press in and turn clockwise to secure into place. The arrow on the hose connector will align with the lock symbol. 2 To remove the hose, press in and turn the hose connector counter- clockwise to unlock and remove. 3 Select the desired cleaning tool for use. Follow the cleaning tool sub assembly instructions for the selected tool. 4 Attach the cleaning tool by inserting the hose stem into the handle of the cleaning tool. Press in and turn clockwise at the same time to secure and press in and turn counter clockwise to release. Check for proper connection by turning the handle counter-clockwise a few turns. The handle should remain connected. (Note for reference: This connection method is the same design used with most over the counter prescription bottles). The design of this connection is to prevent the hose from twisting and kinking during use. 1 1 Attach the Steam Bottle Nozzle. Aligning the arrow located on the Steam Bottle Nozzle with the Un-Lock symbol located on the Nozzle Connector. Press in and turn clockwise to secure into place. The arrow on the nozzle will align with the Lock symbol. 2 To remove the Steam Bottle Nozzle, turn counter-clockwise to unlock and remove. Cleaning Tip: The wedge tip and squared edges reach into tight areas often missed or difficult to reach with traditional cleaning methods. The Wedge sides concave to wrap around sink and faucet fixtures, door knobs, and other small curved surfaces leaving them clean all around. Multiple sides provide more surface cleaning area and allow one to clean with one side and finish with the other for a “NOW YOU KNOW THAT’S CLEAN” performance. Surface examples for use are countertops, tabletops, cabinets, walls, floor spot cleaning, bathroom fixtures and more. 5 6 WEDGE CLEANING TOOL ASSEMBLY 5 Slide the wedge shaped cleaning pocket over the wedge cleaning tool frame until it is completely on. 6 Secure the cleaning pocket onto the frame. Close the cinch by pulling on the elastic band and sliding the locking bean to tighten. Cleaning Tip: The wedge cleaning pocket was designed for cleaning a variety of surfaces and is exceptional on those that are large and flat, both horizontal and vertical. Broad cleaning sides and super absorbent microfiber fabrics loosen, lift, and lock in dirt and grime while sanitizing at the same time. CAUTION: It is recommended that you allow the cleaning pockets to cool off before removing them from the wedge or cylinder tools to avoid possible scalding injury. Using Your Portable Steam Pocket® - cont’d DETAIL SCRUBBING BRUSH ATTACHMENT 1 Press fit the detail scrubbing brush onto the detail cleaning handle. Cleaning Tip: The scrubbing brush attachment is great for hard to reach areas and for breaking up heavily soiled and dried on messes. Allow plenty of time for steam heat and moisture to penetrate the surface as it dislodges the mess for wiping. It can be especially useful in the bathroom and shower area loosening scum build-up on tile and grout. Select either of the cleaning pocket tools to clean, sanitize, and wipe up excess moisture and residue. NOTE: The detail scrubbing brush is most effective when applying light pressure. Let the super heated steam and the bristle tips do the work for you. The sides of the bristles are not effective for scrubbing. If you apply too much force, you will bend and deform the bristles. CYLINDER CLEANING T...