Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Refer servicing to qualified service personnel. 2. Do not expose the monitor to rain or moisture, and avoid operation in wet areas. Take immediate action if ever the monitor does become wet. Turn power off and refer servicing to qualified service personnel. Moisture can damage the monitor and also create the danger of electric shock. 3. Use both the rearview mirrors and the driver's monitor when backing the vehicle. Avoid using only the driver's monitor to confirm the back of the vehicle since the view range of the driver’s monitor is limited. Rearview Monitor Sidemirrors Note that the left and right sides of the image on the monitor are reversed, just like that of the rearview mirror. Rearview Monitor 5. Do not block the ventilation slits on the monitor. Install the monitor while paying attention to ventilation space for the monitor. 6. Do not use the monitor beyond its temperature, humidity or power source ratings. (a) The ambient temperature must not range beyond 5°F - 140°F (-1 5°C - +60°C). (b) Avoid using the monitor when the humidity is above 90*/.. (c) The input power source for the monitor must be within the specification. Camera - 1 - MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 1. Mode Indicator This indicator shows the operation mode as follows. STANDBY : The indicator will be lit green. ON : The indicator will be lit amber. 2. Mode Selection Switch This switch is a push-push type and is used to select the operation mode as follows. STANDBY : The heater for the monitor's CRT is preheated and all other circuits, including the rear view camera, are shut off. ON : The rear view picture will be displayed on the monitor. 3. Day/Night Selection Switch (BRIGHT, DAY/NIGHT) This switch is a push-push type and is used to control the brightness level of the picture. DAY : Normal brightness level will be displayed. NIGHT: Reduced brightness level will be displayed. 4. Brightness Control (BRIGHT) This control is used to adjust the brightness of the picture on the monitor. 5. Contrast Control (CONTRAST) This control is used to adjust the contrast of the picture on the monitor. -2 - 6. Fixing Holes These 4 holes are used to fix the monitor fixing bracket to the vehicle. 7. Monitor Fixing Bracket This is used to install the monitor to the vehicle. 8. Monitor Fixing Screws These 4 screws are used to secure the monitor. The tilt of the monitor can be changed approx. 30° (20° : Upper or 10° : lower) by loosening these screws. 9. Distance Panel 10. Camera Cable Connector (CAMERA) This connector is used to connect the optional camera cables GP~CA40(33ft, 10m), or GP-CA41 (66ft, 20m). 11. Camera Cable (Sold Separately) 12. Power Source and Remote Connector (DC IN/REMOTE) This 4-pin connector is used to connect the power and remote cable. Pin No.1 : Ground Pin No.2 : Ground Pin No.3 : Remote Input (Reverse position) Pin No.4 : DC-j- 12V or DC+24V Input 12 3 4 < Front View> 13. Fuse Holder Caution : When replacing the fuse, use only the specified one (3A, Part NO. XBA1C30NU100). INSTALLATION Caution : It is suggested to protect the camera cable during installation to prevent damage to the cable. 1. Remove the 4 monitor fixing screws which are hold the monitor and remove the monitor fixing bracket. 2. Secure the monitor fixing bracket by using 4 bolts (obtained locally (6mm/bolt)). 3. Secure the monitor onto the monitor fixing bracket by using the supplied 4 monitor fixing screws and adjust the tilt of the monitor. 4. Connect the optional camera cable to the camera cable connector (CAMERA) on the rear of the monitor. 5. Connect the supplied remote cable to the power source and to the remote connector (DC IN/REMOTE) on the rear of the monitor. 7. Connect the +12V/24V wire (Red) to the + 12V/24V line which is electrically after the ignition switch, the remote input wire (Blue) to the +12V/24V line for the reverse light and the ground wire (Green) with lug to the chassis of the vehicle. - 4 - ADJUSTMENT OPERATING PROCEDURE The following adjustment should be made by qualified service personnel or system installers. 1. Adjust the camera's tilt by first loosening the 4 hex bolts and then tilting the camera so that the rear bumper positions on the reference line of the distance panel on the monitor screen. Rear Bumper Caution: The distance lines indicated on the distance panel are distances on ground . level. Obstacles in mid air may seem to be more distant than they actually are. 1. Turn the ignition switch to the ON position and confirm that the Mode Indicator LED lights to green (STANDBY mode). 2. Whenever changing the gear shift lever to the reverse position, the Mode Indicator LED turns to amber (ON mode) and the rearview picture can automatically be seen on the monitor screen in a few seconds. Lights to Amber 3. Whenever changing the gear shift lever to other than the reverse position, the Mode Indicator LED turns to green and the picture on t...