Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
For this reason you should use the third hand to hold small workpieces. . Avoid placing the hot soldering tip in contact with the plastic parts of the multifunctional holder. Failure to observe this advice may result in damage to the device. . If a dangerous situation arises, pull the mains plug immediately out of the mains socket. CAUTION! DANGER OF POISONING! Do not breathe air contaminated with soldering fumes. When working with the device for long periods do not allow the fumes from soldering to build up. They may be hazardous to health. Always provide adequate ventilation of your working area. In addition, it is recommended that you wear protective gloves, a face mask and a protective apron. GB/IE/CY Safety advice Do not eat, drink or smoke in rooms where soldering is carried out. Otherwise your hands may transfer any adhering traces of lead via food or cigarettes into your body. . Always wash your hands immediately after soldering . . Do not dispose of soldering waste with the household rubbish. Soldering waste must disposed of as special waste. 4. Careful handling and use of electrical power tools a) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. b) Look after the device carefully. Check for broken parts or parts that are damaged to the extent they detrimentally affect the functioning of the device. Have any damaged parts repaired before you use the device. Many accidents have their origins in poorly maintained electrical tools. GB/IE/CY 33 Safety advice / Before first use . Original accessories / attachments . Use only the accessories detailed in the operating instructions. The use of attachments or accessories other than those recommended here could lead to you suffering an injury. . Before first use . Fitting the helical spring . Insert the narrower end of the helical spring 3 into the opening of the multifunctional holder 7 . Ensure that the outwardly bent end of the helix points upwards and insert it into the recess provided for it in the multifunctional holder 7 (see arrow in Fig. B). Push the helical spring into the opening as far as it will go. Turn the helical spring 3 clockwise to fix the multifunctional holder 7 in place. . Inserting / replacing soldering tips CAUTION! DANGER OF BURNS! Allow the soldering pencil to heat up without a soldering tip. Removal of a soldering tip 2 or a copper attachment 9 10 11 may only be done when the appliance has been switched off and the soldering tip or attachment has cooled down. . All soldering tips and attachments have a screw thread and can, therefore, be easily and quickly replaced on the soldering pencil 1 . Turn the soldering tip or attachment anti-clockwise to remove it. Turn the soldering tip or attachment clockwise to fix it in place. GB/IE/CY Operation Operation Switching on and off Switching on: Insert the mains plug into a suitable mains socket. Switching off: Pull the plug out of the mains socket to switch off the device. Third hand CAUTION! DANGER OF BURNS! The clips on the third hand 5 can become hot while you are soldering the workpiece. 1. Fold out the third hand 5 upwards. 2. Rotate the clips 4 until they are oriented in the required direction. 3. Clamp the workpiece between the two clips 4 . Solder sponge CAUTION! The hot soldering tip 2 must never be placed in contact with a dry solder sponge 8 , otherwise the solder sponge may be damaged. The solder sponge 8 is used to clean soldering tips. Moisten the solder sponge 8 before you use it. GB/IE/CY Operation . Soldering — The soldering pencil has a rated output of 30 watts and is therefore ideal for electronics soldering. — The design of the soldering pencil makes it especially suitable for use where access is difficult or for fine soldering work. — To achieve the best results use electronics solder 1.0 (10 g electronics solder with integrated flux is included) or 1.5 mm diameter 100 % Sn. We recommend the use of soldering paste (not soldering grease or soldering fluid) as a flux. Clean the soldering tip 2 on the moist solder sponge 8 . After cleaning the tip 2 it must be “tinned” (coated with solder). This is done by melting solder on to the hot soldering tip 2 . Guide the soldering tip 2 to the intended joint site and heat the joint. . Place the solder (with flux) between the joint site and the tip 2 to melt it. . Continue to feed further solder until the whole joint has a covering of solder. . Then quickly remove the soldering tip in order to avoid overheating the molten solder. . Allow the solder to harden while not subjecting it to vibration or movement. . Note: The flux is either already contained in the solder or applied separately. Ask the advice of the retailer when buying solder in order to choose the most suitable solder...