Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• Damage to eyes if effective goggles are not worn • Risk of injury unless hands are kept well clear of cutting devises Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Operation WARNING. Before connecting a tool to a power source, be sure that the voltage supply is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. Setting up the iron stand 1. By firmly holding the stand with both hands, press the centre of the stand in so that it separates itself from the rest of the stand and bend to approximately 45° from the base. Switch on 1. Ensure the soldering iron is resting securely on the iron stand before plugging in to the power. 2. After switching on the power, allow the tool a few minutes to heat up to its operating temperature. Switch off 1. It is highly recommended that the soldering tip is wiped clean on a damp sponge (not included) after use to prolong service life and performance. 2. Place the soldering iron securely on its stand. Switch off the tool at the power switch and unplug the unit. For safety, please ensure the unit is well minded until it has entirely cooled down. Preparing to solder WARNING. Always use safety glasses and ensure the work area is well ventilated to help avoid breathing in dangerous fumes. The GMC Soldering Iron is typically used to melt and apply solder on various surfaces including circuit boards. 1. Before beginning to solder, secure the work piece so that it does not move and affect your accuracy. 2. Prepare a damp sponge nearby to clean the tip when required. 3. Melt a small amount of solder onto the tip of the iron (1). This process is known as ‘tinning’ and will assist the heat in following from the soldering iron’s tip, to the solder joint. It is important to do this immediately with new soldering tips. 3. Ensure that the workpiece and soldering tip are clean. The workpiece can be cleaned with the use of a small file or knife blade. It is recommended that the user wipe clean the soldering tip with a damp sponge before, during and after soldering. This will help promote a cleaner and stronger solder joint. Soldering 1. Hold the soldering iron close to the base of the handle (5), and just above the flange (4) like a pen. WARNING. Never touch the shaft (3) or tip (1) as temperatures can range up to 400°C. 2. Hold the soldering iron with the tip pressed onto the workpiece for a few second to allow it to heat up. 3. Slowly feed the solder onto the joint, not the soldering iron, allowing the solder to melt onto the joint. 4. Once the solder has been applied to the joint, hold the workpiece still while removing the solder and soldering iron simultaneously. NOTE. A good solder joint will appear smooth and shiny. If this is not the case, you will need to reheat the joint and re-apply the solder. Removing the tip WARNING. Do not attempt to remove the tip while the soldering iron is still hot. 1. To help prevent the tip from bonding to the shaft, which may cause the heater element to burn out, it is recommended that the tip (1) be removed after each use. 2. To remove the tip (1), clamp the soldering iron and apply two phillips head screwdrivers to the screws just above the soldering tip (2) and turn anti- clockwise until the screws are loose and remove the tip. Full 2-Year Warranty This product is warranted for a 2-year period for home domestic use from the date of the original purchase. If found to be defective in materials or workmanship, the tool or the offending faulty component will be replaced free of charge with another of the same item. A small freight charge may apply. The warranty replacement unit is only made available by returning the tool to the place of purchase with a confirmed register receipt. Proof of purchase is essential. We reserve the right to reject any claim where the purchase cannot be verified. This warranty does not include damage or defects to the tool caused by or resulting from abuse, accidents, alterations or commercial or business use. Consistent with our product development programme, improvements may have been made which render the contents of the tool’s packaging or user instructions slightly different to the product received. Phone (03) 8346 1100 Facsimile (03) 8346 1200 Email info@gmca.com.au Website Copyright Global Machinery Company Australia Proprietary Limited, 2001 Dear customer, if you require any help with your product, whether it is a Warranty Claim, spare part or user information, please pho...