Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This book is provided as a GENERAL GUIDELINE and the information contained herein may differ from your vehicle. DISCLAIMER: Crimestopper Security Products, Inc. and its vendors shall not be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into a vehicle in which all systems and associated components are in perfect working condition. TECHNICAL SUPPORT (800)-998-6880 Monday -Friday 8:00am -4:30pm Pacific Time Website: CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET SIMI VALLEY, CA. 93063 REV 12.2008 This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. Such modification could void the user's authority to operate the equipment. TABLE OF CONTENTS Cautions & Warnings and Component Mounting ..…..………………………………………………………………………3 Antenna Diagram…….………….…………………………....……………...……………………………………………..……4 Wiring Information….……….…………………………....……………...……………………………………………..……5-11 Shock Sensor …….………….…………………………....……………...……………………………………………..……12 Power Door Lock Wiring, Systems & Diagrams.........……………...….………..…….……..…………...……………13-15 Tachless, Tach Reference, Tach Finder, Timed Crank Modes………..……………………………………………....16-18 Diesel Glow Plug Delay………………………………………………………………………………………………...………19 Programmable Options, Options Reset……….………………………………………………….………….………...…19-25 Remote Transmitter / Transceiver Programming…………………………………......…..…………………...…...…...….26 2-Vehicle Operation……………………………………………………………………………………………………...……..27 Alarm Trigger Diagnostics…………………....…………………………………………………………………….………….28 Remote Start Diagnostics………….……………………..………………………………………...…………………...…….28 Jumper Pin Diagram…………………………………………………………………………………………………………....29 System Wiring Diagram, DATA Port Diagram..…………………………………………………………….……………30-32 PR PRE-INSTALLATION CONSIDERATIONS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY). PLAN OUT YOUR INSTALLATION. You should pre-determine the location of the Control Module (Brain), Valet button, LED, and Siren locations. This will save time and ease the installation process. USE VOLT/OHM METER to test and locate all connections. Test Lights or Lighted Probes could possibly damage a vehicle’s computer system or cause an airbag to deploy. ADDITIONAL PARTS, that are not included with this unit, may be needed for your particular vehicle. These items may include extra relays, Door Lock Interface Modules, or Transponder Override modules. 2 CAUTIONS & WARNINGS DAMAGE RESULTING FROM IMPROPER INSTALLATION IS NOT COVERED UNDER WARRANTY!! DO NOT remote start your vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes. DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with the brake/gas pedals, steering column, or any other moving parts in the vehicle. REMOVE MAIN SYSTEM FUSE(S) before jump-starting the vehicle or charging the battery at high boost. DAMAGE MAY OCCUR TO SYSTEM IF PROPER PRECAUTIONS ARE NOT OBSERVED. DO NOT exceed the rated output current of any circuit on the Remote start module. Failure to observe this warning will result in damage to the unit. Output currents are listed where applicable throughout this manual. DO NOT extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition switch wiring. Extending these wires could result in poor performance. COMPONENT MOUNTING CONTROL MODULE: The alarm control module should be mounted in a concealed location. DO NOT mount the control unit in the engine compartment. Fasten the module to a bracket or wire harness using the cable ties provided. SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body metal near the siren. LED: Mount the Blue LED in a visible location on the dashboard or console. SHOCK SENSOR: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to firewall or side paneling. OVERRIDE/PROGRAM/VALET BUTTON: Mount the Override/Program push-button in a hidden but accessible location. This button is required for emergency disarm, programming, and valet mode. 3 ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS WIRING: 9-PIN Connector Green: MODE A: (-) Start Activation Input This wire allows an outside source or accessory to activate a Remote Start. A 1-secon...