Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Specifications Electrical Requirements 120 V~ / 60 Hz / 3.9 A Bulb 500W / 120 V~ Halogen (included) E229796 Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Set Up Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Risk of accidental starting; resulting in serious personal injury. Turn the Power Switch of the Light OFF and unplug it from the electrical outlet before assembling or making any adjustments. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Deviation from the assembly instructions may result in a risk of fire or electric shock. Slide the Bracket (13) over the Lower 1. Grip (14), lining the hole in the Bracket up with the bolt hole in the Grip. Insert the Knob (20) through the Con2. cave Washer (34) and into the hole. Remove the Bolt (38) at the top of the 3. housing and open the Lamp Cover (24). Insert the Bulb (27) into the Bulb 4. Socket (18). Do not touch the Bulb with your bare hands; oil from skin will drastically shorten the life span of the bulb if not cleaned with rubbing alcohol and allowed to dry before use. Handle the bulb with a soft, clean cloth or clean work gloves instead. Close the Lamp Cover (24) and se5. cure with the Bolt (38). FIGURE A 6. Gently squeeze the Wire Cover (25) while placing its four tabs into the Lamp Cover (24). Secure the tab on the Wire Cover to the Lamp Cover using the Screw (39). (See Figure A.) WARNING WARNING Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Plug the Light into a standard, 1. grounded 120V electrical outlet. Press the Switch on the back of the 2. unit to turn the Light on. WARNING! Keep the Light away 3. from combustible objects. The light and housing will get hot enough to start a fire. To prevent accidents, turn off the 3. Light and disconnect its power supply after use. Clean, then store the Light indoors out of children’s reach. Maintenance And Servicing Risk of serious personal injury from accidental starting or electric shock. Turn the Power Switch of the Light to its “OFF” position and unplug the Light from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. Cleaning, maintenance, and lubrication BEFORE EACH USE,1. inspect the general condition of the Light. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the Light with clean, moist cloth. WARNING! If the supply cord of 3. this Light is damaged, it must be replaced only by a qualified service technician. WARNING PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/ or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. PARTS LIST PartDescriptionQty 1Power Cord1 2Screw M4*164 3Junction Box Cover1 4Pad For Junction Box Cover1 5Junction Box Base1 6Junction Box Hex Sleeve1 7Sleeve2 8Bolt M4*61 9Fasten Bracket1 10Bolt M6*142 11Washer2 12Hex Nut4 13Bracket1 14Lower Grip1 15Upper Grip1 16Shell1 17Soft Sleeve1 18Bulb Socket1 19Bolt M4*63 20Knob M6*161PartDescriptionQty 21Reflector1 22Glass1 23Seal Ring1 24Lamp Cover2 25Wire Cover1 26Plastic Long Plug1 27Bulb1 28Switch Cover1 29Switch 1 30Wire Nut1 31Wire Press Board1 32Screw M4*122 33Plastic Short Plug3 34Concave Washer 1 35Large Washer1 36Gear Washer1 37Spring Washer1 38Bolt1 39Screw1 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Assembly diagram LIMITED 90 DAY WARRANTY Harbo...