Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• Confirm that the paper tray guides are set in place. • Confirm that the top of the stack is not higher than the limit mark indicated on the tray guide. . If a paper misfeed still occurs, contact your sales or service representative. . Do not leave any torn paper scraps within the printer. When "Misfeed: A" Appears A Open lower right cover 1. B Remove the misfed paper from inside of lower right cover 1. ZAEH041E Note . If no misfed paper can be seen inside the cover, slide out the paper tray and check the loaded paper, and then return the tray. Removing Misfed Paper 65 4 C Close lower right cover 1. Note . Close the cover by pushing the center area of the cover. When "Misfeed: B" Appears A Open the duplex unit by lifting the catch. B Open the right cover by lifting the catch. C Remove the misfed paper from inside of the right cover. D Close the right cover before closing the duplex unit. E If the misfed paper is inside of the bypass tray, while lifting the paper guide lever (A), remove the misfed paper (B). ZAEP331E ZAEH050E ZAEY190E ZAEY191E Troubleshooting 66 4 When "Misfeed: C" Appears When the interchange unit is not installed A Open the right cover by lifting the catch. B Open the upper right cover by pulling the handle, and remove the misfed paper. C Close the upper right cover before closing the right cover. When the interchange unit is installed A Open the duplex unit by lifting the catch. B Open the right cover by lifting the catch (A), and open the upper cover of the interchange unit by pulling the handle (B). C Remove the misfed paper. D Close the covers in the following order: the upper cover of the interchange unit, the right cover, and the duplex unit. ZAEP140E ZAEP270E ZAEP331E ZAEH051E ZAEH060E Removing Misfed Paper 67 4 When "Misfeed: D" Appears A Open the duplex unit by lifting the catch. B Open the right cover by lifting the catch (A), and open the upper cover of the interchange unit by pulling the handle (B). C Remove the misfed paper. D If the misfed paper was not removed in step C, open the upper cover of the bridge unit (A), and remove the misfed paper (B). E Close the upper cover of the bridge unit. F If the misfed paper was not removed in step D, open the right cover of the bridge unit (A), and remove the misfed paper (B). G Close the covers in the following order: the right cover of the bridge unit, the upper cover of the interchange unit, the right cover of the printer, and the duplex unit. ZAEP331E ZAEH051E ZAEH060E ZAEY070E ZAEY080E Troubleshooting 68 4 When "Remove Misfeed from Mailbox" Appears A Open the cover of the mailbox. B Remove the misfed paper. C Close the cover of the mailbox. When "Remove Misfeed From Finisher" Appears SR510 (500–sheet finisher) A Remove the misfed paper inside of the finisher tray. B If the misfed paper was not removed in step A, open the upper cover of the finisher (A) and remove the misfed paper (B). C Close the upper cover of the finisher. ZAEH090E ZAEY100E ZDEY010E ZDEY020E Removing Misfed Paper 69 4 SR720 (1000–sheet finisher) A Remove the misfed paper inside of the finisher tray. B If the misfed paper was not removed in step A, open the right cover of the finisher. C Remove the misfed paper. D Close the right cover of the finisher. E If the misfed paper was not removed in step C, open the front cover of the finisher (A), and remove the misfed paper (B). F Close the front cover of the finisher. When "Misfeed: Y" Appears A Open lower right cover 2. B Remove the misfed paper inside of the cover. C Close lower right cover 2. ZAEY110E ZAEH111E ZAEY120E ZAEY130E ZAEH140E ZAEY150E Troubleshooting 70 4 When "Remove Misfeed from Duplex Unit" Appears A Open the duplex unit by lifting the catch. B While lifting the lever, lift cover Z1 (A), and remove the misfed paper (B). C If the misfed paper was not removed in step B, while lifting the lever, lift cover Z2 (A), and remove the misfed paper (B). D Close cover Z2, and then cover Z1. E Close the duplex unit. ZAEP331E Z1 ZAEY160E Z2 ZAEY170E Adding Staples Adding Staples When “Add Staples” appears on the SR720 (1000–sheet finisher) panel display, the staples have run out. Follows these steps to add a new A Open the front cover of the fin- staple refill. isher. Note . After adding the staple refill, staples might not be ejected for the first few times. A Remove the empty cartridge. SR510 (500–sheet finisher) A Open the rear cover of the finisher. 4 BRemove the empty cartridge. ZAEH180E ZDEX020E BRemove the empty cartridge. ZDEX030E ZAEH181E BRemove the empty refill case as shown in the illustration. ZAEH190E 71 Troubleshooting C Align the arrows on the new refill SR510 (500–sheet finisher) case and the cartridge, and push the new refill case in until it A Reinstall the cartridge. It clicks. should click into place. ZAEH191E Note . Do not remove the ribbon for bundling staples, before installing the cartridge. D Pull out the ribbon used for bundling staples. ZAEH200E EReinstall the cartridge. ZDEX031E ZAEH1...