Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
4. Press SNAP to take a picture, or press the MODE button quickly to change mode settings as described above. The camera is set at infinity and will not be focused on an object closer than 49 feet. 5. The mode setting operation is a cycle loop, so press the MODE button to switch to another mode. The loop order of the different modes is shown here: 6. To change settings, toggle through the different modes by pressing the MODE button. When a mode is selected, the indicator symbol on the LCD will appear. You can then select that mode by pressing the SNAP button. 7. When in “Normal” mode, press SNAP to take a picture. Press SNAP-> 8. By pressing the MODE button the camera will enter “Mode Change”. 9. To select “Self-Timer” mode, press MODE and the self -timer mark appears, then press SNAP and the camera will take a picture after a 10 second delay. The camera exits self-timer mode automatically after capture is done and the self-timer mark disappears on the LCD at the same time. Press MODE-> press SNAP to capture. 10. Low Resolution mode, will cause your pictures to be of a lower resolution, but will allow you to store many more pictures in the camera’s memory. The default setting is Hi. To change the resolution, press the MODE button until you see the “mode” icon appears. Press the SNAP button, and Lo will appear. The camera is changed from high resolution to low resolution. Repeat the same steps to change the camera back to Hi resolution mode. CAPTURED PICTURES WITH BUILT-IN MEMORY: Pixels (Resolution) 1280X1024(Hi) Image Quality High quality (HQ) Low quality (LQ) Captured Picture Quantity Up to 40 pictures Up to 55 pictures 1024X768(Lo) High quality (HQ) Low quality (LQ) Up to 55 pictures Up to 85 pictures 11. When in “Normal” mode press the MODE button 3 times to enter the “AVI” mode. The icon will appear. Press the SNAP button to start AVI capturing, and counting. The resolution for AVI is 320X240 pixies. The memory of the camera can hold from 40-70 seconds of live action. It depends on what objects you are capturing and the lighting conditions. 12. To delete all pictures in the camera’s memory, select the “Delete All” mode. This represented by the trash can icon. Press the SNAP button to confirm. The picture number will then blink. You will hear a tone that becomes higher as the pictures are deleted. Once complete, the picture number will reset to possible captured numbers. 13. If the “delete Last” icon appears, the display will show the following: Press SNAP to delete the last picture in the camera’s memory. The picture number will be automatically increased after deletion is done. 14. Press the MODE button until SET mode appears on the LCD. Press SNAP to enter Setting mode. To change the setting of image quality (default setting is High), Storage/PC Cam (default setting is Storage), 50 Hz/60 Hz frequency (default setting is 60 Hz). a. Select the image quality at Hq (High quality) or Lq (Low quality) by pressing the SNAP button. Then press the MODE button to confirm and enter next setting. c. Select 50 Hz or 60 Hz settings for the camera output by pressing the SNAP button. Then press MODE button to confirm and enter next setting. The camera’s default mode is the “60” mode, which matches the power frequency for the United States. To change to the “50” mode, press the SNAP button until the “60” changes to “50”. Confirm the selection by pressing the SNAP button. To avoid any flickering on the picture, the correct power frequency (either 50 or 60) for your country must be selected. d. Escape the Setting mode by pressing the SNAP button. 15. The battery mark keeps tracking the battery life. If the battery indicator is blinking, it is necessary to replace the batteries soon. b. Select the STO (Mass Storage) or PCC (PC CAM) mode by pressing the SNAP button. Then press MODE button to confirm and enter next setting. DOWNLOADING THE PICTURES TO YOUR COMPUTER 1. The camera has a mass storage function. When connected to the PC without changing any setting, a new disc icon will appear in the computer interface. Click the icon, the captured pictures will be seen directly. 2. The captured pictures can also be downloaded and saved in the PC via the photo imaging software. CONNECTING TO THE COMPUTER System Requirements: Pentium 166MMX minimum (Recommended Pentium 266) Windows 98 / Me / Windows 2000 / XP Minimum 32MB of RAM USB port Minimum 200MB of Hard Drive space with additional 65 MB space for IE and DirectX CD-ROM driver Super VGA Monitor and video card SOFTWARE INSTALLATION For OS Windows Me/2000/XP, no need to install software, just plug in and use. Load software prior to connecting your camera to your computer if your OS is Windows 98. To load software insert CD into your CD-ROW drive and it will self-start. The CD contains the Roxio Photo Suite software as well as the drivers that will allow your computer to recognize your camera. Follow the “On Screen” instructions. If your computer does not have an auto play fun...