Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Woodstock Dateigröße: 1.89 mb Dateiname: Unterrichtssprache:

Note—The tables slide into place easily if you lift up while you slide them into place. 4. Place a straightedge across the top of the wings, and tighten the nuts behind the edge of the extension wings to secure the wings in place. Figure 10. Extension wing box inventory. Figure 11. T-bolt and rail T-slot. Figure 12. Sliding in the wings. -8 ADJUSTMENTS The SHOP FOX® W1716/W1720 Aluma-Classic™ Fence requires little adjustment since most of the features are built in at the factory. The primary adjustment is to position the fence so it is parallel to the saw blade. Fence Parallelism If your table saw has been properly adjusted, the saw blade should be parallel to the miter slot. Refer to your table saw manual for the proper procedure to check and adjust the saw blade to the miter slot correctly. To adjust the SHOP FOX® Aluma-Classic™ Fence parallel with the miter slot, do these steps: 1. UNPLUG THE TABLE SAW! 2. Align the edge of the fence with the edge of the miter slot. 3. Lock the fence and check the alignment between the left edge and the miter slot. 4. Adjust the setscrews shown in Figure 13 to adjust the angle of the fence. Note— The left setscrew will move the fence left and the right setscrew will move the fence right. 5. Adjust the fence until the back end falls 1.64" away from the miter slot so the work- piece clears the opposite end of the saw blade without binding. This is called “lead” (pronounced leed). KICK-BACK! DO NOT cut on the left side of the blade if the fence lead is adjusted for cutting on the right side of the blade. Re- adjust the lead when changing the side of the blade you are cutting on. -9 Figure 13. Fence adjustment setscrews. DISCONNECT power to the saw at this time! Otherwise, serious injury may occur. ADJUSTMENTS 1.64" Shown exaggerated for illustration purposes. Figure 14. Lead adjustment. Scale Installation & Adjustment The self-adhesive scale provides fast and accurate fence positioning. It is best to install the scale after all other adjustments in this section have been made. Figure 15 shows the scale properly installed on the front rail. To install the scale indicator, do these steps: 1. UNPLUG THE TABLE SAW! 2. Raise the blade to its maximum height. 3. Position the fence against the right side of the blade. 4. Carefully place the scale along the front rail about 1.2" away from the edge and underneath the scale indicator. Note—Do not stretch the tape! This will cause inaccurate cuts. 5. Position the “0” mark on the scale under the cursor hairline and secure the scale to the rail. 6. Adjust the cursor left or right so the hairline is directly over the “0” mark on the scale. 7. Make a test cut then measure the thickness of your test board. 8. Fine tune the hairline indicator to correspond with the actual test board thickness. This method accounts for any vibration or wobble that may be present in the spinning blade. Figure 15. Scale installed on front rail. ADJUSTMENTS -10 W1716 SHOP FOX® Aluma-Classic™ Fence 5 1 3 23 6 223 5 5 17 12 25 15 37 20 21 37 24 8 14 35 36 32 33 3423 29 30 29 38 9 39 19 18 7 26 PARTS -11 W1716 SHOP FOX® Aluma-Classic™ Fence REF PART # DESCRIPTION 1 X1716001 FENCE BODY ASSEMBLY 3 X1716003 FENCE SIDEBOARD 4 X1716004 FENCE PLUG 5 X1716005 FENCE SIDEBOARD CAP 6 X1716006 ADJUSTMENT BOLT 5.16"-18 7 X1716007 CLAMP 8 X1716008 HANDLE 9 X1716009 FEMALE KNOB 12 X1716012 CLEAR INDICATOR 14 X1716014 SLIDER 19 X 50 X 2T 15 XPSS05 SETSCREW 5.16"-18 X 1.4" 16 XPW03 FLAT WASHER #10 17 XPS06 PHLP HD SCR 10-24 X 3.8" 18 XPB25 HEX BOLT 3.8"-16 X 13.4" 19 PB88 HEX BOLT 1.4"-20 X 13.4" 20 XPLN02 LOCK NUT 1.4"-20 21 XPLN01 LOCK NUT 3.8"-16 22 XPS24 PHLP HD SCR 8-32 X 3.8" 23 XPN02 HEX NUT 5.16"-18 24 X1716024 ALUMA-CLASSIC™ LABEL 25 X1716025 WARNING LABEL (SHORT) 26 X1716026 SLIDER 19 X 50 X 1.2T 29 XPW07 FLAT WASHER 5.16" 30 X1716030 REAR RAIL 32 X1716032 FRONT RAIL 33 XPFH25 FLAT HD SCR 5.16"-18 X 1 34 X1716033 FRONT RAIL BRACKET 35 XPB05 HEX BOLT 1.4"-20 X 3.4" 36 X1716036 SCALE 30" 37 XPSS05 SETSCREW 5.16"-18 X 1.4" 38 XPSB03 CAP SCREW 5.16"-18 X 1 39 X1716039 CLAMP PLUG PARTS -12 PARTS 5 4 1 5 3 23 6 3 22 5 5 17 16 12 25 15 37 20 21 37 8 14 26 9 39 19 18 7 24 201 202 203 204 131 114 141 113 123 121 111 140 123 113 141 127 102 103 134 131 131 134 115 141 131 113 124 126 122 118 141 113 124 W1720 SHOP FOX® Aluma-Classic™ Fence -13- W1720 SHOP FOX® Aluma-Classic™ Fence REF PART # DESCRIPTION REF PART # DESCRIPTION 1 X1716001 FENCE BODY ASSEMBLY 3 X1716003 FENCE SIDEBOARD 4 X1716004 FENCE PLUG 5 X1716005 FENCE SIDEBOARD CAP 6 X1716006 ADJUSTMENT BOLT 5.16"-18 7 X1716007 CLAMP 8 X1716008 HANDLE 9 X1716009 FEMALE KNOB 12 X1716012 CLEAR INDICATOR 14 X1716014 SLIDER 19 X 50 X 2T 15 XPSS05 SETSCREW 5.16"-18 X 1.4" 16 XPW03 FLAT WASHER #10 17 XPS06 PHLP HD SCR 10-24 X 3.8" 18 XPB25 HEX BOLT 3.8"-16 X 13.4" 19 XPB119 HEX BOLT 1.4"-20 X 13.4" 20 XPLN02 LOCK NUT 1.4"-20 21 XPLN01 LOCK NUT 3.8"-16 22 XPS24 PHLP HD SCR 8-32 X 3.8" 24 X1716024 ALUMA-CLASSIC™ LABEL 25 X1716025 WARNI...

Herunterladen

Geben Sie zwei Ziffern: