Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Woodstock Dateigröße: 1.87 mb Dateiname: Unterrichtssprache:

1 Drill and Tap ................................. 1 Blade Guard Clamp Bag • V-Clamp .................................. 1 • L-Bracket ................................. 1 • Locking Plate ............................ 1 • Hex Bolt 1.4-20 X 11.2" ................. 2 • Flat Washer 1.4" ......................... 4 • Hex Nut 1.4-20 ........................... 2 • Hex Bolt 5.16-18 X 3.4" ................. 1 • Flat Washer 5.16" ....................... 2 • Hex Nut 5.16-18 .......................... 1 Rail Mounting Bags • Hex Bolt 1.4-20 X 3.4" ................... 4 • Hex Bolt 3.8-16 X 1".....................4 • FlatHdScr 1.4-20X 3.4".................2 • Flat Washer 1.4" ........................10 • Flat Washer 3.8" ......................... 8 • Hex Nut 1.4-20.............................2 • Hex Bolt M10-1.5 X 25 ................. 4 Legs ........................................... 2 Support Bracket..............................2 Feet ............................................ 2 Leg Mounting Bag • Hex Nut 1.2-12.............................2 • Flat Washer 3.8" ......................... 8 • Hex Bolt 1.4-20 X 1.2" .................. 4 • Flat Washer 1.4" ......................... 4 • Hex Bolt 3.8-16 X 5.8" ................... 2 Note—Extra mounting hardware has been included to compensate for differences between table saws. You may not need all of the hardware that is included in the inventory. Shop Fox® Classic Fence -5 -6- Shop Fox® Classic Fence Figure 2. Mounting the front and back rails. 3. Position the back rail so its top edge is flush with the table top and the rectangular cut-outs are in line with the miter slots. See Figure 1. UNPLUG the saw power cord, and TURN OFF the power switch before you begin fence installation procedures. Accidental saw startup while installing or adjusting the fence will result in serious personal injury. Rail Installation On most saws, the mounting holes for the rails will match the existing rail mounting holes. On the saws where the mounting holes do not line up, see Correcting Mounting Hole Misalignment on Page 14 for instructions on drilling new holes. Metric and standard hex bolts have been included to fit most common rail installations. Mounting the Back Rail 1. Remove the mounting hardware for the blade guard which extends over the back edge of the table. (Be sure to reinstall the guard after completion.) 2. Locate the back fence rail (the rail with the two rectangular cut-outs on one edge and one cutout on the other edge) and set it against the rear edge of the table saw. Figure 1. Attaching the back rail. 4. Attach the rail using the mounting hardware from the old rail or two 3.8"-16 x 1" or M10-1.5 X 25 hex head bolts and washers. Secure as shown in Figure 2. Shop Fox® Classic Fence -7- Mounting The Front Rail 1. Align the side of the front rail with two rectangular cutouts against the edge of the table. 2. Set the top edge of the front rail so it is flush with the table top and the cutouts are in line with the miter slots. If your saw table has a beveled front edge, then align the top of the rail with the bottom edge of the bevel. See Figure 3. Figure 3. Attaching the front rail bracket. Bottom Edge of Bevel 3. Attach the rail using the mounting hardware from the old rail or two 3.8"-16 x 1" or M10-1.5 X 25 hex head bolts and washers. Secure as shown in Figure 2. Figure 4. Shimming the front tube. Mounting The Front Rail Tube 1. Orient the machined flat edge of the tube so it faces the table edge. 2. Thread four 1.4-20 X 3.4" hex bolts and 1.4" washers through the rail and into the threaded holes in the bottom of the tube. 3. If your table has a beveled front edge, it may be necessary to install spacers or shims between the rail and the rectangular tube as shown in Figure 4. The spacers should equal approximately the height of the bevel (3.8" on most saws). Four to six washers installed with each of the four attachment screws should raise the height of the tube enough to assure clearance of the fence above the table surface. 4. Mount the fence on the rails and check the clearance between the bottom edge of the HDPE facing and the table top. 5. Add or remove shims from the tube to rail mounting until a clearance of at least 1.16" is achieved. Note—This clearance should never exceed 1.8", as this can allow material to get under the fence during certain types of sawing operations. Note: Do not install the scale at this time. Fence 1. Raise the lock handle up to release the fence locking tab and place the fence down on the rails. 2. Make sure the angle bracket of the fence assembly fits easily into the slot created by the front rail bracket and rectangular tube. • If any binding is experienced, loosen the rail mounting bolts and adjust the rails. 3. Install the fence, and check to see that it slides smoothly along the rails without binding or catching on the table surface. • If any binding is experienced, loosen the rail mounting bolts and adjust the rails. 4. Make sure you keep ...

Herunterladen

Geben Sie zwei Ziffern: