Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
The next screen shows page 2 of the System Information menu. System Information Serial Port 1......................3F8h, IRQ 4 Serial Port 2......................2F8h, IRQ 3 Parallel Port......................378h, IRQ 7 PS/2 Mouse.........................Installed The sections below explain the parameters. AcerAltos 500L User’s Guide Processor The Processor parameter specifies the type of processor currently installed in your system. The system supports Intel Pentium II processors. Processor Speed The Processor Speed parameter specifies the speed of the processor currently installed in your system. The system can support Pentium II processors running at 233, 266, 300, 333, 350, and 400 MHz and Celeron processors running at 266 MHz. Internal Cache Size This parameter specifies the first-level or the internal memory (i.e., the memory integrated into the CPU) size, and whether it is enabled or disabled. External Cache This parameter specifies the second-level cache memory size currently supported by the system. The available cache sizes are 256 KB or 512 KB (depending on the CPU installed). For information on how to configure the system memory, see Memory Configuration. Floppy Drive A This parameter specifies the system’s current diskette drive A settings. Floppy Drive B This parameter specifies the system’s current diskette drive B settings. Chapter 3 BIOS Utility 3-5 IDE Primary Channel Master This parameter specifies the current configuration of the IDE device connected to the master port of the primary IDE channel. IDE Primary Channel Slave This parameter specifies the current configuration of the IDE device connected to the slave port of the primary IDE channel. IDE Secondary Channel Master This parameter specifies the current configuration of the IDE device connected to the master port of the secondary IDE channel. IDE Secondary Channel Slave This parameter specifies the current configuration of the IDE device connected to the slave port of the secondary IDE channel. Total Memory This parameter specifies the total amount of onboard memory. The memory size is automatically detected by BIOS during the POST. If you install additional memory, the system automatically adjusts this parameter to display the new memory size. 1st Bank/2nd Bank/3rd Bank The 1st Bank, 2nd Bank, and 3rd Bank parameters indicate the type and size of DRAM installed in DIMM sockets 1, 2, and 3 respectively. The None setting indicates that there is no DRAM installed. For the location of the DIMM sockets, refer to the System Board Layout in Chapter 2. AcerAltos 500L User’s Guide Serial Port 1 This parameter shows the serial port 1 address and IRQ setting. Serial Port 2 This parameter shows the serial port 2 address and IRQ setting. Parallel Port This parameter shows the parallel port address and IRQ setting. PS/2 Mouse The BIOS utility automatically detects if there is a pointing device connected to your system. If there is, this parameter displays the Installedsetting. Otherwise, it is set to None. Chapter 3 BIOS Utility Product Information The Product Information contains the general data about the system, such as the product name, serial number, BIOS version, etc. This information is necessary for troubleshooting (may be required when asking for technical support). The following figure shows how the Product Information screen appears: Product Information Product Name...........................xxxxxxxxx System S/N.............................xxxxxxxxx Main Board ID..........................xxxxxxxxx Main Board S/N ........................xxxxxxxxx System BIOS Version....................v3.1 DMI BIOS Version.......................2.00.1 Product Name This parameter specifies the official name of the system. System S/N This parameter specifies the system’s serial number. Main Board ID This parameter specifies the system board’s identification number. AcerAltos 500L User’s Guide Main Board S/N This parameter specifies the system board’s serial number. System BIOS Version This parameter specifies the version of the BIOS utility. DMI BIOS Version This parameter specifies the version of the DMI (Desktop Management Interface) BIOS version. DMI enables software to collect information about a computer environment. Chapter 3 BIOS Utility Disk Drives Select Disk Drives to input configuration values for disk drives. The following screen shows the Disk Drives menu: Disk Drives Diskette Drive A.......................[xx-MB, xx-inch] Diskette Drive B.......................[ None ] LS-120 Drive as........................[ Normal ] • IDE Primary Channel Master • IDE Primary Channel Slave • IDE Secondary Channel Master • IDE Secondary Channel Slave Floppy Drives To enter the configuration value for the first floppy drive (drive A), highlight the Floppy Drive A parameter. Press or to view the options and select the appropriate value. Possible settings for the Floppy Drive parameters are: • [ None ] • [360 KB, 5.25-inch] • [1.2 MB, 5.25-inch] • [720 KB, 3...