Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
44 3 Setting up your computer PS/2 keyboard Plug your PS/2 keyboard cable into the PS/2 keyboard port (purple port) located on the rear panel of your computer. 45 Connecting a monitor The location of your monitor port depends on which Veriton 3600 models you have. Refer to “Rear panel - VT3600D” on page 16 or “Rear panel - VT3600G” on page 18 to locate your monitor port(s). To connect a monitor, simply plug the monitor cable into the monitor port (blue port) located on the rear panel of your computer. Note: Refer to the monitor manual for additonal instructions and information on adjusting your monitors settings. Note: The image above shows the Vertion 3600G. Refer to pages 16 and/or 18 for the location of your monitor port(s). 46 3 Setting up your computer Connecting the power cable Caution! Before you proceed, check the voltage range in your area. Make sure that it matches your computer’s voltage setting . If they don’t match, set your computer’s voltage selector switch to the voltage range applicable to your area. Set the voltage selector switch to the voltage range applicable to your area (a). Plug the power cable into the power cable socket located on the rear panel of your computer (b). Then plug the other end of the power cable into a power outlet. Turning on your computer After connecting the necessary peripherals and plugging in the power cable, you are now ready to turn the computer on and get to work. To turn on your computer: 1 Turn on all peripherals connected to your computer such as the monitor, printer, fax, speakers, etc. 2 On the front panel of your computer, press the Power button. Important: Make sure that the power cable is properly plugged into an electrical outlet. If you are using a power strip or an AVR (Auto-Voltage Regulator), make sure that it is plugged in and turned on. 3 Setting up your computer Turning off your computer To turn off your computer, follow the steps below. For Windows XP: 1 On the Windows XP taskbar, click on the Start button, and click Turn Off Computer; then click Turn Off. 2 Turn off all peripherals connected to your computer. For Windows 2000: 1 On the Windows 2000 taskbar, click on the Start button, highlight Shut Down, select Shut down from the drop down window then click on OK. 2 Turn off all peripherals connected to your computer. If you cannot shut down your computer normally, press the power button for at least four seconds. Quickly pressing the button may put the computer in Suspend mode only. 49 Connecting options Connecting your printer Your computer supports parallel, serial and USB printers. To connect a parallel printer, plug the printer cable into the parallel port (burgundy port) located on the rear panel of your computer. Note: The printer shown below is for your reference only. Actual device model may vary in select countries. Note: If you are using a serial printer, connect the printer cable into the serial port located on the rear panel of your computer. In the same manner, connect a USB printer by plugging the printer cable into any of the USB ports located on the front or rear panels. 50 3 Setting up your computer Connecting the modem (optional) Set up your modem connection by plugging the telephone line and handset line into their corresponding ports on the rear panel of your computer. 51 Connecting to the network You can connect your computer to a Local Area Network (LAN) using a network cable. To do so, simply plug the network cable into the network port (white port) on the rear panel of your computer. Note: Consult your network system administrator or operating system manual for information on how to configure your network setup. 3 Setting up your computer Connecting multimedia devices You can connect multimedia devices such as microphone, earphone or headphone, external speakers, and audio line-in device. These devices will allow you to take advantage of your computer’s multimedia features. Note: The multimedia devices shown below are for your reference only. Actual device models may vary in select countries. Plug the devices in as follows: Note: For information on how to configure multimedia devices, consult the documentation that came with each device. • microphone: connects to the microphone-in jack (pink port) located on the front and rear panel of your computer Note: The system has two microphone-in jacks (front and rear). However, you can not use both of them at the same time. By default, your system enables the microphone-in jack in front and disables the one at the back. • earphones, headphones: connect to the Headphone-out port (lime port) located on the front panel of your computer Note: To adjust the volume of the headphones, click on the Volume icon located on the taskbar at the bottom of your screen. When the Volume control pops up, drag the Volume control lever to the desired level. You can also use the Volume control button on the keyboard. 54 3 Setting up your computer • external speakers: connect to the Audio-out/Lin...