Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
So it's possible that your new case may differ slightly from the descriptions in this manual. This isn't a problem; it's simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec's Computer Enclosures. For more comprehensive instructions on installing your motherboard and peripherals, please refer to the user's manuals which come with your components and drives. Super LANBOY User's Manual Anodized Aluminum Super Mini Tower Case We don't include a power supply with the Super LANBOY. So you're free to choose one that best suits your needs. Make sure you choose a PS/2 size power supply that conforms to the ATX standard and is compatible with your motherboard. Most systems conform to either the ATX12V or ATX2.03 standard. Setting up 1. Take the case out of the box. Remove the Styrofoam and the plastic bag. 2. Place the case upright on a flat surface, with the rear of the case facing you. 3. Remove the thumbscrews from the right side panel. Open the case by pulling the panel away from the case. 4. Inside the case, you'll see wiring with marked connectors (USB, PWR etc.), an installed I/O panel and a power cord. 5. Swing the front panel open. You'll see a toolbox with a picture frame on To open the toolbox, simply push on it. To lock it into position, push on again. Inside the toolbox, you can store hardware or small tools (screws, brass standoffs, plastic stands, etc.) Installing the power supply 1. With the case upright, place the power supply in the top rear Note: most dual-fan power supplies should be installed with the towards the bottom of the case. 2. Push the power supply to the back of the case and 3. Attach the power supply to the case, using the Installing the motherboard This manual does not cover CPU, RAM, consult your motherboard manual for troubleshooting. 1. Lay the case down, with the be visible. 2. Make sure you have the panel provided with the board manufacturer 3. Line up your motherboard holes are lined holes; this is 1 4. Lift your motherboard away from the standoff holes. 5. Screw the brass standoffs into the threaded holes that line up with your motherboard. Do not overtighten the standoffs. Some standoffs may be preinstalled for your convenience. 6. Place your motherboard on the brass standoffs. 7. Attach your motherboard to the standoffs with the provided Phillips-head screws. Your motherboard is now installed. Connecting the Power Switch and LEDs 1. Connect the 20-pin ATX power connector from your power supply (and AUX or +12V connectors if appropriate) to your motherboard. 2. The Reset switch (labeled RESET SW) connects to your motherboard at the RST connector. Make sure you always attach the colored wire to Pin 1, and the black wire to ground. 3. Connect the Power Switch (labeled POWER SW) to the PWR connector on the motherboard. 4. The Power LED, Hard Drive LED, and Speaker connectors all share a single ribbon cable. Attach the POWER LED, HDD LED connector and SPEAKER connectors to the appropriate headers on your motherboard. Connecting the USB ports There are two black 5-pin USB connectors on cables attached to the front bezel. Here's how to connect them to your motherboard headers: 1. Check the USB pin layout in your motherboard's user manual and make sure it follows this standard pinout: Pin 1: USB Power - may also be labeled +5V Pin 2: Negative Signal - may also be labeled P-, D-, USB0-, etc. Pin 3: Positive Signal - may also be labeled P+, D+, USB0+, etc. Pin 4: Ground Pin 5: Ground 2. Plug the 5-pin USB connectors onto the header rows so that is on Pin 1 (Power, or +5V). The second header may be pin at the opposite end of the row) so be careful when connectors. Connecting the Audio Ports There are seven individual wires and connectors for speaker and microphone. Attach them 1. Locate the internal audio connectors 2. Consult your motherboard or sound 3. Connect the MIC connector to 4. Connect the MIC-BIAS connector 5. Connect the AUD GND connector 6. Connect the FPOUT-R 7. Connect the FPOUT-8. Connect the RET-9. Connect the RET-Note: If your motherboard 2 to connect the RET-R or RET-L connectors. Installing 5.25" Devices The Super LANBOY features three external 5.25" drive bays. A metal plate covers each drive bay opening. 1. For each drive bay you wish to use, carefully remove the metal plate covering the bay by twisting it back and forth until it separates from the case. If you don't wish to use a drive bay, leave the corresponding metal plate in place. Note: Watch your fingers. When you remove the metal plate, there may be a sharp metal burr remaining where the plate was attached. 2. Remove the thumbscrews from the left side panel and detach the left side panel from the case. 3. Slide your 5.25" drive into the open drive bay, so that it is flush with the front bezel. Secure the drive with the provided screws. (You'll find openings for the screws o...