Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
For additional safety best practices information, see the Regulatory Compliance Homepage at Display Bezel Removing the Display Bezel 1. Remove the display assembly (see Display). 2. Remove the four rubber bumpers from the top and mylar tapes from the bottom of the display bezel. 3. Remove the six screws on the display bezel. 4. Using your fingertips, carefully pry up the inside edge of the display bezel. 5. Remove the display bezel. Replacing the Display Bezel 1. Align the display bezel over the display panel, and gently snap into place. 2. Replace and tighten the six screws. 3. Replace the display assembly (see Replacing the Display Assembly). Display Panel Removing the Display Panel NOTICE: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel. 1 rubber bumper (4) 2 screw (6) 3 display bezel 4 display panel CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at 1. Remove the display assembly (see Display). 2. Remove the display bezel (see Removing the Display Bezel). 3. Remove the six screws securing the display panel assembly to the display cover. 4. Disconnect the cables from the connectors on each end of the inverter board. 5. Remove the display panel assembly. 6. Remove the eight screws (four on each side) that secure the display panel brackets to the display panel. Replacing the Display Panel 1. Align the display panel brackets with the display panel. 2. Replace the eight screws that secure the display panel brackets to each side of the display panel. NOTE: Make a note of the routing of the cables behind the display panel. 1 display panel 2 screw (6) 3 display inverter 4 display cover 1 display panel bracket (1 left; 1 right) 2 display bracket screw (8 total; 4 on each side) CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at 3. Align the display panel with the display cover and replace the six screws. 4. Connect the display cables to the ends of the inverter board. 5. Route the cables back through their routing channels. 6. Replace the display bezel (see Replacing the Display Bezel). 7. Replace the display assembly (see Display). Display Panel Cable Removing the Display Panel Cable 1. Remove the display assembly (see Display). 2. Remove the display bezel (see Removing the Display Bezel). 3. Remove the display panel (see Removing the Display Panel). 4. Turn over the display panel and remove the conductive tape on the display board. 5. Disconnect the flex cable from the display board. Replacing the Display Panel Cable 1. Connect the flex cable to the connector on the inverter board. 2. Connect the flex cable to the connector on the back of the display panel and adhere the tape back into position. 3. Replace the display panel (see Replacing the Display Panel). 4. Replace the display bezel (see Replacing the Display Bezel). 5. Replace the display assembly (see Replacing the Display Assembly). Display Inverter NOTE: The Display Panel cables and connectors may differ depending on the Display Panel you ordered. 1 display board connector 2 flex cable 3 conductive tape CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at Removing the Display Inverter 1. Remove the display assembly (see Display). 2. Remove the display bezel (see Removing the Display Bezel). 3. Disconnect the cables from the connectors on either side of the inverter board. 4. Lift out the inverter board from the securing plastic tabs. Replacing the Display Inverter 1. Align the holes on the inverter board with the tabs on the display cover and snap it into position. 2. Connect the cables on either side of the inverter board. 3. Replace the display bezel (see Replacing the Display Bezel). 4. Replace the display assembly (see Display). Back to Contents Page 1 inverter board 2 connector (2) CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at Back to Contents Page System Fan Dell™ Vostro™ A840/A860 Service Manual Removing the System Fan Replacing the System Fan Removing the System Fan 1. Follow the instructions in "Before You Begin" on page 9. 2. Remove the palm rest(see Removing the Palm Rest). 3. Disconnect the fan cable from the system board connector. 4. Remove the two screws securing the system fan to the computer cover. 5. Lift the system fan out. R...