Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
PC Notebooks - Latitude 100L (133.99 kb)
PC Notebooks - Latitude 100L (133.82 kb)
Anleitung Zusammenfassung
1 pull-tab on bottom flex-cable connector 2 top flex-cable connector 3 display connector 4 inverter connector 5 display cable see Mini RSL 8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. Installing the Display Panel 1. Connect the top flex-cable connector to the display panel connector. 2. Connect the bottom flex-cable connector to the inverter connector. 3. Lay the display panel in the top cover. 4. Route the display-feed flex cable so that it rests in the notch located in the bottom edge of the top cover. 5. Replace the four M2 x 3-mm screws that secure the display panel to the top cover. 6. Replace the display bezel. Display Latch Assembly Removing the Display Latch Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the keyboard. 3. Remove the display assembly. 4. Remove the display bezel. 5. Remove the two M2.5 x 5-mm screws that secure the display latch assembly to the top cover. 6. Lift the display latch assembly up and out of the top cover. 1 spring hook (top cover) 2 spring 3 spring hook (display latch) 4 display latch assembly see Mini RSL 5 M2.5 x 5-mm screws (2) 63PDH 6 top cover see Mini RSL Installing the Display Latch Assembly 1. Attach one end of the spring to the spring hook on the left edge of the display latch, and attach the other end of the spring to the spring hook in the top cover. 2. Align the screw holes in the display latch assembly with the screw holes in the top cover. 3. Replace the two M2.5 x 5-mm screws that secure the display latch assembly to the top cover. Back to Contents Page Back to Contents Page Palm Rest Dell™ Latitude™ 100L Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the hard drive. 3. Remove the CD or DVD drive. 4. Remove the keyboard. 5. Remove the EMI shield. 6. Remove the display assembly. 7. Turn the computer over and remove the twelve M2.5 x 8-mm screws (not labeled). 8. Remove the M2.5 x 4-mm screw from the battery bay. 9. Turn the computer back over and remove the two M2.5 x 5-mm screws from the top of the palm rest. 10. Disconnect the touch pad connector from the system board. NOTICE: Carefully separate the palm rest from the base plastics to avoid damage to the palm rest. 11. Starting at the back center of the palm rest, use your fingers to separate the palm rest from the base plastics by lifting the inside edge of the palm rest. Back to Contents Page Back to Contents Page Microprocessor Thermal-Cooling Assembly Dell™ Latitude™ 100L Service Manual Removing the Microprocessor Thermal-Cooling Assembly Installing the Microprocessor Thermal-Cooling Assembly Removing the Microprocessor Thermal-Cooling Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the keyboard. 3. Remove the EMI shield. 4. Disconnect the fan power cable from the system board. 5. Loosen in consecutive order the four captive screws, labeled "1" through "4," that secure the microprocessor thermalcooling assembly to the system board. 1 captive screws (4) 2 fan power-cable connector 6. Pull up the microprocessor thermal-cooling assembly by the pull-tab to lift the assembly out of the system board. Installing the Microprocessor Thermal-Cooling Assembly NOTICE: Before you install the replacement microprocessor thermal-cooling assembly, remove the mylar that covers the thermal grease on the assembly. 1. If you are installing a replacement microprocessor thermal-cooling assembly, remove the mylar that covers the thermal grease on the assembly. If you are installing the assembly that you removed in the previous section: a. Wipe the thermal grease off of the microprocessor thermal-cooling assembly with a clean paper towel. b. Squeeze all of the contents of the thermal grease packet (provided with the kit) on to the microprocessor thermal-cooling assembly. 2. Place the back of the microprocessor thermal-cooling assem...