Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
87 (UK/Brazil). 90 (Japan) Layout QWERTY Camera Pixel 1.3 megapixel Video resolution 640 x 480 at 30 fps (maximum) Diagonal viewing angle 66° Touch Pad X/Y position resolution (graphics table mode) 240 cpi Size: Width 84.45 mm (3.32 inches) sensor-active area Height 41.6 mm (1.64 inches) rectangle Battery Type 3-cell lithium ion 6-cell lithium ion Attributes 3-cell 6-cell Depth 23.1 mm (0.91 inches) 45.62 mm (1.80 inches) Height 39.04 mm (1.54 inches) 45.7 mm (1.80 inches) Width 204.14 mm (8.04 inches) 214.0 mm (8.42 inches) Weight 0.165 kg (0.36 lb) 0.350 kg (0.77 lb) Voltage 11.1 VDC 11.1 VDC Charge time when the computer is off (approximate) 3.0 hours (3-cell) 4.0 hours (6-cell) Operating time Battery operating time varies depending on operating conditions and can be significantly reduced under certain power-intensive conditions. For more information, see the Dell Technology Guide on your hard drive or at support.dell.com. Life span (approximate) 300 discharge/charge cycles Temperature range: Operating 0° to 35°C (32° to 95°F) Back to Contents Page Storage –40° to 65°C (–40° to 149°F) Coin-cell battery CR-2032 AC Adapter Input voltage 100–240 VAC Input current (maximum) 1.5 A Input frequency 50–60 Hz Output power 65 W Output current 3.34 A (continuous) Rated output voltage 19.5 ± 1 VDC Dimensions: Height 16 mm (0.63 inches) Width 66 mm (2.6 inches) Length 127 mm (5 inches) Weight (without cables) 0.25 kg (0.55 lbs) Temperature ranges: Operating 0° to 35°C (32° to 95°F) Storage –30° to 65°C (–22° to 149°F) Physical Height 16.4 mm to 25.8 mm (0.64 inches to 1.01 inches) Width 292 mm (11.49 inches) Depth 214 mm (8.42 inches) Weight (with 3-cell battery): Configurable to less than 1.35 kg (2.98 lbs) Computer Environment Temperature range: Operating 0° to 35°C (32° to 95°F) Storage –40° to 65°C (–40° to 149°F) Relative humidity (maximum): Operating 10% to 90% (noncondensing) Storage 5% to 90% (noncondensing) Maximum vibration (using a random-vibration spectrum that simulates user environment): Operating 0.66 GRMS Non-Operating 1.3 GRMS Maximum shock (for operating: measured with Dell Diagnostics running on the hard drive and a 2-ms half-sine pulse; for non-operating: measured with hard drive in head-parked position and a 2-ms half-sine pulse): Operating 110 GRMS Non-Operating 160 GRMS Altitude (maximum): Operating –15.2 to 3048 m (–50 to 10,000 ft) Storage –15.2 to 10,668 m (–50 to 35,000 ft) Airborne contaminant level G2 or lower as defined by ISA-S71.04-1985 Back to Contents Page Memory and Processor Board Dell™ Inspiron™ 11 Service Manual Removing the Memory and Processor Board Replacing the Memory and Processor Board Removing the Memory and Processor Board 1. Follow the procedures in Before You Begin. 2. Remove the battery (see Removing the Battery). 3. Remove the keyboard (see Removing the Keyboard). 4. Remove the palm rest (see Removing the Palm Rest). 5. Disconnect the speaker cable from the speaker cable connector on the I/O board (see Removing the Speakers). 6. Remove the hard drive (see Removing the Hard Drive). 7. Remove the memory module (see Removing the Memory Module). 8. Remove the palm rest bracket (see Removing the Palm Rest Bracket). 9. Remove the processor heat sink (see Removing the Processor Heat Sink). 10. Remove the four screws that secure the memory and processor board to the computer base. 11. Use your fingertips to carefully spread apart the securing clips on either side of the memory and processor board connector until the board pops up. 12. Lift the memory and processor board off the system board. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on your computer). CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. CAUTION: When the memory and processor board is removed from the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge" in the safety instructions that shipped with your computer). 1 screws (4) 2 memory and processor board connector 3 securing clips (2) 4 memory and processor board Replacing the Memory and Processor Board 1. Follow the procedures in Before You Begin. 2. Align the notch in the memory and processor board with the tab in the connector. 3. Slide the memory and processor board firmly into the slot at a 30-degree angle, and press the memory and processor board down until it clicks into place. If you do not ...