|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Back to Contents Page NOTE: To get maximum performance/dual-channel memory bandwidth capability, both memory module connectors must contain memory modules and the modules must be of the same size and configuration. NOTE: If a memory module is not installed properly, the computer does not boot. NOTICE: If the memory module cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer. Back to Contents Page Modem Dell™ Inspiron™ 6400/E1505 Service Manual Removing the Modem Replacing the Modem Removing the Modem 1. Follow the instructions in Before Working Inside Your Computer. 2. Turn the computer upside-down, loosen the two captive screws on the cover, and remove the cover from the computer. 3. Remove the M2 x 3-mm screw that attaches the modem to the system board. 4. Pull up on the pull-tab to disconnect the modem from the modem connector on the system board. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: To help prevent damage to the system board, you must remove the main battery (see Before Working Inside Your Computer) before you begin working inside the computer. 1 modem connector on system board 2 pull-tab 3 modem 4 modem cable 5 M2 x 3-mm screw 5. Disconnect the modem cable from the modem. Replacing the Modem 1. Connect the modem cable to the modem. 2. Connect the modem to the system board. Align the connector on the bottom of the modem with the modem connector on the system board, and press down on the right side of the modem. 3. Replace the M2 x 3-mm screw. Back to Contents Page NOTICE: Do not disconnect the modem cable from the system board. NOTICE: Ensure that the modem cable is routed correctly when you replace the modem. Back to Contents Page Optical Drive Dell™ Inspiron™ 6400/E1505 Service Manual Your computer ships with a fixed optical drive installed. 1. Follow the instructions in Before Working Inside Your Computer. 2. Turn the computer upside-down and remove the M2.5 x 8-mm device security screw labeled with a lock icon ( ). 3. Insert a screwdriver into the indentation for the device security screw, and push the notch on the metal tab toward the media bay to release the optical drive from the media bay. 4. Pull the drive out of the media bay. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To help prevent damage to drives, store them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them. 1 optical drive in media bay 2 indentation for M2.5 x 8-mm device security screw 3 notch Back to Contents Page Palm Rest Dell™ Inspiron™ 6400/E1505 Service Manual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest 1. Follow the instructions in Before Working Inside Your Computer. 2. Remove the optical drive (see Optical Drive). 3. Remove the hinge cover (see Removing the Hinge Cover). 4. Remove the keyboard (see Keyboard). 5. Remove the display assembly (see Removing the Display Assembly). 6. Remove the eleven remaining 2.5 x 8-mm screws from the bottom of the computer. 7. Turn the computer top-side up and loosen the palm -rest captive screw. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: To help prevent damage to the system board, remove the main battery (see Before Working Inside Your Computer) before working inside the computer. NOTE: The screw locations may vary slightly from the image shown below. 1 2.5 x 8-mm screws (11) 8. Disconnect the touch pad connector and the standby switch connector from the system board. 9. Lift the palm rest and remove it from the computer. Replacing the Palm Rest 1. Align the palm rest with the bottom plastics and gently snap it into place. 2. Reconnect the touch-pad connector and the standby switch connector to the system board. 3. Tighten the palm -rest captive screw. 4. Turn the computer upside-down, and replace the eleven M2.5 x 8-mm screws on the bottom of the computer. 5. Replace the display assembly (see Replacing the Display Assembly). 6. Replace the keyboard (see Keyboard). 7. Replace the hinge cover (see Replacing the Hinge Cover). Back to Contents Page 1 standby switch connector 2 touch pad connector Back to Contents Page Pin Assignments for I/O Connectors Dell™ Inspiron™ 6400/E1505 Service Manual USB Connector Video Connector S-Video TV-Out Connector IEEE 1394 Connector USB Connect...
Dieses Handbuch ist für folgende Modelle:PC Notebooks - Inspiron E1505 (1.41 mb)