Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
The cards are keyed to prevent incorrect insertion. If card orientation is not clear, see the documentation that came with the card. 1. Hold the card with its orientation symbol pointing into the slot and the top side of the card facing up. The latch may need to be in the in position before you insert the card. 2. Slide the card into the slot until the card is completely seated in its connector. If you encounter too much resistance, do not force the card. Check the card orientation and try again. The computer recognizes most PC Cards and automatically loads the appropriate device driver. If the configuration program tells you to load the manufacturer's drivers, use the floppy disk or CD that came with the PC Card. To install an ExpressCard: 1. Place the ExpressCard in the PC Card adapter (the adapter is included with the ExpressCard). 2. Install the ExpressCard with adapter the same way as a PC Card. NOTICE: Use the PC Card configuration utility (click the icon in the taskbar) to select a card and stop it from functioning before you remove it from the computer. If you do not stop the card in the configuration utility, you could lose data. Do not attempt to eject a card by pulling its cable, if one is attached. 1 release latch 2 PC Card CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Dell™ Product Information Guide. 1 release button 2 PC Card Removing a Smart Card Grasp the smart card by the edge with your fingers, and then pull the card straight out of the computer. Installing a Smart Card You can install a smart card in the computer while the computer is running. The computer automatically detects the card. 1. Hold the card so that the gold contact pad is facing upward and pointing toward the smart card slot. 2. Slide the smart card into the smart card slot until the card is completely seated in its connector. The smart card will protrude approximately 1/2 inch from the slot. 1 slot 2 ExpressCard CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Dell™ Product Information Guide. NOTE: You can remove a smart card from the computer while the computer is running. 1 smart card blank CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Dell™ Product Information Guide. 1 gold contact pad 2 smart card (top) If you encounter too much resistance, do not force the card. Check the card orientation and try again. Back to Contents Page 1 smart card blank Back to Contents Page Speaker Dell Precision ™ M2300 Service Manual 1. Follow the instructions in Before You Begin. 2. Remove any installed media bay device (see Media Bay Devices). 3. Remove the hinge cover (see Hinge Cover). 4. Remove the keyboard (see Removing the Keyboard). 5. Remove the coin-cell battery (see Coin-Cell Battery). 6. Remove the palm rest (see Palm Rest). 7. Disconnect the speaker connector from the system board. 8. Pull the speaker straight up and out of the base. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Dell™ Product Information Guide. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer. 1 speaker connector NOTICE: Handle the speakers with care to avoid damaging them. Back to Contents Page System Board Dell Precision ™ M2300 Service Manual Removing the System Board Installing the System Board Removing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer. The replacement kit for the system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board. 1. Follow the instructions in Before You Begin. 2. Remove any installed media bay device (see Media Bay Devices). 3. Remove any installed smart cards or smart card blanks from the smart card slot (see Removing a Smart Card). 4. Remove the hinge cover (see Hinge Cover). 5. Remove the keyboard (see Removing the Keyboard). 6. Remove the memory module(s) (see Memory). 7. Remove any installed wireless communications cards (see Communications Cards). 8. Remove the palm rest (see Palm Rest). 9. Remove the modem (see Modem). 10. Remove the speaker (see Speaker). 11. Remove the PC Card reader (see PC Card Reader). 12. Remove the processor thermal-cooling assembly (see Processor Thermal-Cooling Assembly). 13. Remove the processor (see Removing the Processor). 14. Disconnect the fan cable from the system board. 15. Disconnect the cables near the WLAN card and the modem connector from the system board. 16. Remove the four M2.5 x 5-mm screws (labeled with silver triangles on the system board). CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Dell™ Pr...