Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When the standby or hibernation function is used under this condition, the date and time may be incorrectly displayed. Correct the date and time, and then install Phoenix APM 2.0 for Windows NT®. When the standby or hibernation function is used frequently, discrepancies may occur in the display of the date and time even if APM 2.0 for Windows NT is installed. You can set the date and time through [Date/Time] in [Start] - [Settings] - [Control Panel]. When the previous item is not the cause PressC F9~) in the Setup Utility (C^1 “Setup Utility”). This will restore the Setup Utility’s settings to their default values (except the password settings). Try removing all peripheral devices. 4Windows]98p • Run SCANDISK to check the hard disk. > At start-up, press C Ctrl 0 to operate the computer in the Safe mode. 4Windows}2000l • Click [Local Disk(C:)] in [My Computer] with the right button, select [Properties], then select [Tools] - [Check Now]. • At start-up, press ( F8 ) to operate the computer in the Safe mode. |Wi ndows.98II4Wi nd ows2000* When resuming from the standby or hibernation mode, [|3| does not appear even if a password has been set in the Setup Utility Use the Windows password as the following. Select [Start] - [Settings] - [Control Panel] - [Power Management]* - [Advanced], then add the check mark for [Prompt for password when computer goes off standby]. [Power Options] 4Windows'2000> 4Windowsl98) When starting up in the MS-DOS mode, the USB floppy disk drive can not be used After powering off the computer, connect the USB floppy disk drive and restart the computer. tWindowsT200Ûl The password of the administrator was forgotten After reinstalling, setup Windows, then set the password again. Troubleshooting Troubleshooting Dealing with Problems (Summary) Starting Up Try the steps listed below. 1 Power off the computer, and then power it on again. 2 When [Press spacebar NOW to ...] is displayed, press the space key. 3 When [Hardware Profile/Configuration Recover Menu] is displayed, follow' the on-screen instructions. Display No display after powering on When there is no display to an external display, • Check your cable connection to the external display. • Confirm your display is powered on. • Check the settings for your external display. Try changing the display by pressing ( Fn ) + ' t ) This combination does not work wrhen the computer is in the Dual- Display Mode. When displaying only through an external display, if the computer is shut down by using the standby or hibernation function, there will be no display on the LCD unless the external display is connected when operations are resumed. In this case, connect the external display or press ( Fn ) + ( F3 ). t WjluilnvaEEn This combination does not work when the computer is in the Dual-Display Mode. The power has not been turned off, but after a certain period of time, there is no display • Has the computer been set to the power-saving mode? To resume operation of your computer from the condition the power of the display is off (for energy conservation purposes), press any key unrelated to the direct triggering of a selection, like CctrD • To save power, your computer may have automatically entered the standby or hibernation mode. (G?3 ^Manuaf6 “Computing On the Road”) Press the power switch. The cursor does not move in scrolling area of the touch pad When the Microsoft® IntelliMouse™ Wheel mode or the original mode is set for the touch pad, only scroll operations are possible for the right part or bottom part of the touch pad. In this case, cursor operations are possible by using the work surface excluding the right part or bottom part. When no mode is set, the entire surface of the touch pad can be used for cursor operations. The cursor cannot be controlled Restart the computer by using the keyboard (e.g., | An afterimage appears (e.g., green, red, and blue dots remain on the display) or there are dots not displaying the correct colors. If an image is displayed for a prolonged period of time, an afterimage may appear. This is not a malfunction. The afterimage will disappear when a different screen is displayed. High-precision and advanced technologies are necessary in the production of color liquid crystal displays (color LCDs). Therefore, if 0.002% or less of the picture elements either fail to light or remain constantly lit (that is, more than 99.998% of elements are functioning properly), no defect is considered to exist. The external display no longer displays properly When an external display not compatible with the power saving mode is used with the computer, the external display may no longer display properly when the computer enters the condition the power of the display is OFF (for energy conservation purposes). In such cases, turn off the power to the external display. The screen becomes disordered • Changing the number of colors of the display may affect the screen. Restart the co...