Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Press to mute the ring tone in the earpiece when there is an incoming call. Earpiece Microphone Battery cover Open to install or replace the battery. Quick reference guide - headset Headset alert tones Three quick beeps VOLUME /+ - keys are pressed when the volume is already at its highest or lowest setting. The headset is not registered and the headset ON/OFF button was pressed. The headset is out of range from the headset base during a call. One short beep every 20 seconds Low battery warning. One short beep every 15 seconds The call is muted. One long beep (repeated) Call waiting alert tone. One short beep The headset ON/OFF key is pressed to go on hook or off hook. Quick reference guide - headset base Charging cradle Insert the headset here for charging. PAIR Press to register or deregister the headset. NO LIFTER MODE light On when NO LIFTER MODE is selected. Flashes while on a call, or another telephone is in use on the same line. Flashes quickly when there is an incoming call. LIFTER MODE light On when LIFTER MODE is selected. Flashes while on a call. Flashes quickly when there is an incoming call. MUTE light On when a call is muted. Quick reference guide - headset base LIFTER AUDIO ADJUST Switch to choose the best headset audio quality when using LIFTER MODE. VOLUME / Press the volume keys on the side of the headset base to adjust the speaking volume while on a call. MODE Press to choose between NO LIFTER MODE or LIFTER MODE when the headset is not in use. The corresponding light turns on. Quick reference guide - headset base Headset base indicator lights NO LIFTER MODE LIFTER MODE MUTE NO LIFTER MODE On when NO LIFTER MODE is selected (default mode). Flashes quickly when there is an incoming call. Flashes when the headset is in use or another telephone on the same line is in use. LIFTER MODE On when LIFTER MODE is selected. Flashes .........................quickly when there is an incoming call. Flashes when the headset is in use. MUTE On when a call is muted. On when you are registering a headset. Flashes when you are deregistering the headset(s) or dial pad from the headset base. Quick reference guide - handset lifter SENSOR ADJ knob Adjusts the sensitivity of the ring detector. ADJUST LIFTER knob Adjusts the height of the lifter arm. Lifter arm Holds the corded telephone handset. Switch hook presser When the CORDED HANDSET CONNECTED switch is set to YES, pressing ON/OFF on the headset raises or lowers the switch hook presser. RING DETECT jack Plug in the auxiliary ring detector. Lifter control cable This cable is hard wired into the lifter and plugs into the LIFTER jack on the headset base. Quick reference guide - handset lifter RING ON/OFF Press to turn the ring detector on or off. When the ring detector is off, the cordless headset does not ring. Switch hook presser adjustment knob Adjusts the position of the switch hook presser. Small lifter pad Holds the earpiece of the corded telephone handset. STATUS light On in red when the ring detector is off. On in blue when the ring detector is on and the headset not in use. Flashes blue four times every three seconds when the ring detector detects an incoming call. Flashes blue slowly when the switch hook presser is raised and you are on a call. Internal ring detector Detects the telephone ringer and sends a ring tone to the headset earpiece. Adhesive tape Remove the protective strips before attaching the lifter to the telephone base. Quick reference guide - handset lifter STATUS light Red On when the headset is not in use and the ring detector is turned off. Flashes slowly when the headset is in use and the ring detector is turned off. Blue On when the headset is not in use and the ring detector is turned on. Flashes four times every three seconds when the ring detector detects an incoming call. Flashes slowly when the headset is in use and the ring detector is turned on. Off The headset base does not have power. The lifter control cable is not plugged into the LIFTER jack on the headset base. Battery installation Install the battery as shown below. After installing the battery, you may be able to make and receive short calls. For optimal performance, charge the headset battery for at least six hours before use. When the headset is not in use, recharge the headset by returning it to the headset base. If the battery compartment cover is attached, press on both sides of the cover and lift it up and off. Insert the battery into the battery compartment with the label THIS SIDE UP facing up. Push the battery plug into the connector inside the compartment according to the color-coded label. Place the wires neatly inside the compartment. Insert the tab on the bottom of the battery compartment cover into the battery compartment. Press down gently on the battery compartment cover until it snaps into place. NOTE: Remove the ear hook from the headset before battery replacement. 1 2 3 4 Battery charging After installing the battery, charge the headset by placing...