Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
1 SAFETY RULES 1. Know your machine. Read this manual carefully. Learn the machine’s applications and limitations, as well as specific potential hazards peculiar to it. 2. Ground all machines. If the machine is equipped with three-pin plug, it should be plugged into a three-pin electrical socket. Never remove the ground pin. 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 4. Do not expose tool to moisture. Don’t use this machinery in damp or wet locations. Keep out of rain. 5. Do not abuse cord. Never use the cord to carry tools or pull the plug from an outlet. Keep cord away from heat, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. 6. Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a moving part of the tool may result in personal injury. 7. Keep work area clean and well lit. Cluttered or dark work areas invite accidents. 8. Keep children away. All children should be kept away from the work area. Never let a child handle a tool without strict adult supervision. 9. Do not operate this tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to operate. 10. Use safety equipment. Eye protection should be worn at all times when operating this machine. Use ANSI approved safety glasses. Everyday eyeglasses only have impact resistant lenses. They are NOT safety glasses. Dust mask, nonskid safety shoes, hard hat, or hearing protection should be used in appropriate conditions. 11. Wear proper apparel. Loose clothing, gloves, neckties, rings, bracelets, or other jewelry may present a potential hazard when operating this machine. Please keep all apparel clear of the machine. 12. Don’t overreach. Keep proper footing and balance at all times when operating this product. 13. Always disconnect the machine from power source before making any adjustments, storing, servicing, or changing accessories. Such preventative safety measures reduce the risk of starting the tool accidentally. 14. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it was designed. 15. Do not use the tool if the switch does not turn it on and off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. 16. Check for damage. Check your tool regularly. If part of the tool is damaged it should be carefully inspected to make sure that it can perform its intended function correctly. If in doubt, the part should be repaired. Refer all servicing to a qualified technician. Consult your dealer for advice. 17. Keep away from flammables. Do not attempt to operate this tool near flammable materials or combustibles. Failure to comply may cause serious injury or death. 18. Store idle tools out of the reach of children and untrained persons. Tools may be dangerous in the hands of untrained users. 19. Maintain tools with care. Keep tools sharp and clean. Properly maintained tools, with sharp cutting edges, are less likely to bind and are easier to control. 20. Never exceed the pressure rating of any component in system. 21. Protect material and air lines from damage or puncture. Keep hose and power cable away from sharp objects, moisture, chemicals, oil, etc. 22. Check condition of hoses before each use. Do not use a damaged hose. If hose is damaged, replace immediately. 23. Read, understand and comply with all warning labels on unit. 24. Drain tank of moisture after each use. If Compressor is not to be used for extended periods of time, leave tank drain valve open to allow moisture to completely drain from tank. 25. Do not tamper with Safety Valve. The Safety Valve is factory set for your model air compressor. Any user adjustments to Safety Valve will automatically void warranty. 26. Air compressors get hot while in operation. NEVER touch the motor, discharge tubing or compressor pump while in operation. 27. The Compressor operates automatically while the motor is turned on. 28. Compressed air from the unit may contain carbon monoxide. Air produced is not suitable for breathing purposes. 29. Always use a respirator when spraying paint or chemicals. 30. The air pressure switch is set at the factory for optimum performance of your equipment. Never attempt to bypass or remove this switch as serious damage to equipment or personal injury could result from excessive air pressure. 2 KNOW YOUR COMPRESSOR Air Filter Handle Air Chuck Pressure Gauges Air Tank Air Regulator Tank Drain Valve Figure 1. Air Compressor Handle: Convenient handle allows for easy transport of your air compressor. Air Regulator: The air regulator controls the air flow pressure. Turn regulator clockwise to increas...