Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
We’re proud of our quality products and we believe in dependable service. You’ll see it in this easy-to-use manual and you’ll hear it in the friendly voices of our customer service department. Best of all, you’ll experience these values each time you enjoy the comfort of your Zoneline. That’s important, because your new Zoneline will be part of your family for a long time. Welcome Staple your receipt to the inside back cover of this manual. You will need it to obtain service under warranty. Write down the model and serial numbers here. They are on a label behind the room cabinet on the base pan. Model number Serial number Date of purchase Before using your Zoneline Need Help? Before you call for service, there are a few things you can do to help us serve you better. Read this manual. It contains instructions to help you use and maintain your Zoneline properly. Save time and money. Check the section titled If Something Goes Wrong before calling. This section was designed to solve common problems that might occur. If you do need service, you can relax knowing help is only a phone call away. Toll-free customer service numbers are included in the back of this manual. Or call the GE Answer Center® at 800.626.2000, 24 hours a day, 7 days a week. Help us help you 800.626.2000 2 Start Here! IMPORTANT SAFETY INFORMATION READ ALL SAFETY INFORMATION BEFORE USING READ ALL SAFETY INFORMATION BEFORE USING • This Zoneline must be properly • Unplug or disconnect the installed in accordance with the Zoneline at the fuse box or Installation Instructions before it circuit breaker before making is used. See pages 10-12. any repairs. • Repair or replace immediately NOTE: We strongly recommend all electric service cords that have that any servicing be performed become frayed or otherwise by a qualified individual. damaged. SAVE THESE INSTRUCTIONS Replacing an existing unit? For details see the Installation Instructions in the back of this manual. Operating Instructions TEMP CONTROLS MODE CONTROLS The LOW controls on your Zoneline WARMER 1 COOLER FAN HIGH STOP FAN LOW LOW HEAT COOL HIGH HIGH HEAT COOL 2 Temp Control The temp control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to COOLER (blue) the indoor air will become cooler. Turn the knob to WARMER (red) and the indoor air will become warmer. 3200 Series only When the outdoor temperature is lower than 25° F., heat is provided by the electric heater in the air conditioner instead of by the heat pump. 2 Mode Control HIGH COOL and LOW COOL provide cooling with different fan speeds. HIGH HEAT and LOW HEAT provide heating with different fan speeds. LOW FAN or HIGH FAN provides air circulation and filtering without cooling or heating. NOTE: If you move the switch from a cool or heat setting to STOP or to a fan setting, the unit has an automatic 3-minute delay before allowing the compressor to restart in the cool or heat mode. 5 Energy Tip Keep the vent control at CLOSE. The room air will be filtered and circulated. The ventilation control lever is located at the lower left side of the Zoneline unit, behind the room cabinet. When set at CLOSE, only the air inside the room is circulated and filtered. When set at OPEN, some outdoor air will be drawn into the room. This will reduce the heating or cooling efficiency. 3 4 3 4 Ventilation Control Air Direction OPEN CLOSE To adjust the air direction, remove the room cabinet. Remove the 7 louver screws that hold the louvers in place. Flip the louver section 180°, replace the screws and the room cabinet. Vent control Remove the room cabinet and flip the louvers to change the air direction. Louver screws Louver screws Operating Instructions Other Zoneline features About Your Heat Pump 3200 Series only Heat pumps can save money by removing heat from the outside air—even when the outside temperature is below freezing— and releasing that heat indoors. To get the best performance from your heat pump, don’t change the room thermostat very often. Raising the heat setting 2–3 degrees will cause the Zoneline to use its electric heating elements in order to reach the new temperature setting quickly. There is a three minute minimum compressor run time at any setting to prevent short cycling. The indoor fan motor starts before the compressor and stops after the compressor cycles off. The electric heating elements use much more electricity than heat pumps and cost more to operate. To Remove the Room Cabinet Additional controls are located To replace: Place the tabs over behind the room cabinet. the top rail. Push inward at the bottom until it snaps into place. To remove: Pull out at the bottom to release it from the tabs. Then lift up. 1 2 12 Auxiliary Controls The auxiliary controls are located behind the room cabinet on the front of the unit control box. The factory settings will be in the DOWN position. The owner is responsible for checking switches ...