Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
6. Remove pump mounting screws securing pump (one on each side). 7. Carefully slide pump from brackets and out of the way. 8. Using an adjustable wrench remove the regulator manifold. 9. Apply pipe sealant to new regulator manifold and assemble, tighten with wrench. 10. Reapply pipe sealant to safety valve. 11. Reassemble all components in reverse order of removal. Make sure to orient gauges to read correctly and use wrenches to tighten all components. Pump Mounting Screw 14 - ENG STORAGE STORAGE Before you store the air compressor, make sure you do the following: 1. Review the Maintenance section on the preceding pages and perform scheduled maintenance as necessary. 2. Drain water from air tank. See To Drain Tank under Maintenance. Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture. 3. Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind air hose loosely around the compressor handle. Wrap electrical cord onto the cord wrap as shown. 4. Store the air compressor in a clean and dry location. Cord Wrap SERVICE REPLACEMENT PARTS REPLACEMENT PARTS Use only identical replacement parts. For a parts list or to order parts, visit our service website at You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at 1-(888)-848-5175. SERVICE AND REPAIRS All quality tools will eventually require servicing and/or replacement of parts. For information about PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our website at or call our Customer Care Center at 1-(888)-848-5175. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.). ACCESSORIES Since accessories, other than those offered by PORTER-CABLE, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only PORTER-CABLE recommended accessories should be used with this product. A complete line of accessories is available from your PORTER-CABLE Factory Service Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site for a catalog or for the name of your nearest supplier. 15 - ENG TROUBLESHOOTING TROUBLESHOOTING Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor to cool. PROBLEM Excessive tank pressure - safety valve pops off. Air leaks at fittings. Air leaks in air tank or at air tank welds. Air leaks between head and valve plate. Air leak from safety valve. Knocking Noise. CAUSE Pressure switch does not shut off motor when compressor reaches "cut-out" pressure. CORRECTION Move On/Off lever to the "Off" position, if the outfit does not shut off contact a Trained Service Technician. Pressure switch "cutout" too high. Tube fittings are not tight enough. Defective air tank. Leaking seal. Possible defect in safety valve. Possible defect in safety valve. Contact a Trained Service Technician. Tighten fittings where air can be heard escaping. Check fittings with soapy water solution. Do Not Overtighten. Air tank must be replaced. Do not repair the leak. Risk bursting. Do not drill into, weld or otherwise modify air tank or it will weaken. The tank can rupture or explode. Contact a Trained Service Technician. Operate safety valve manually by pulling on ring. If valve still leaks, it should be replaced. Remove and clean, or replace. 16 - ENG PROBLEM Pressure reading on the regulated pressure gauge drops when an accessory is used. Compressor is not supplying enough air to operate accessories. Regulator knob has continuous air leak. Regulator will not shut off air outlet. CAUSE CORRECTION It is normal for "some" pressure drop to occur. If there is an excessive amount of pressure drop when the accessory is used, adjust the regulator following the instructions in the Description of Operation paragraph in the Operation Section. NOTE: Adjust the regulated pressure under flow conditions (while accessory is being used). Prolonged excessive use of air. Decrease amount of air usage. Compressor is not Check the accessory large enough for air requirement. If air requirement. it is higher than the SCFM or pressure supplied by your air compr...