Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
If the power disconnect is out of sight, lock in the open position and tag it to prevent unexpected application of power. Failure to do so could result in fatal electrical shock! 3. Release all pressure within the system before servicing any component. 4. Drain all liquids from the system before servicing. 5. Secure the discharge line before starting the pump. An unsecured discharge line will whip, possibly causing personal injury and/or property damage. 6. Check hoses for weak and worn condition before each use, making certain that all connections are secure. 7. Periodically inspect the pump and system components. Perform routine maintenance as required (See Maintenance Section). ! CAUTION This utility pump is not constructed to handle laundry discharge or any other application which may contain caustic chemicals and/or foreign materials. Pump damage could occur if the pump is used in these applications. 8. Provide a means of pressure relief for pumps whose discharge line can be shut-off or obstructed. 9. Personal Safety: a. Wear safety glasses at all times when working with pumps. b. Keep work area clean, uncluttered and properly lighted; replace all unused tools and equipment. c. Keep visitors at a safe distance from the work area. 10. When wiring an electrically driven pump such as this, follow all electrical and safety codes, as well as the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA). 11. This equipment is only for use on 120 volt (single-phase) and is equipped with an approved 3-conductor cord and 3-prong, grounding-type plug as shown in Figure 1. To reduce the risk of electric shock, the motor must be securely and adequately grounded. This can be accomplished by inserting plug directly into a properly installed and grounded 3-prong, grounding-type receptacle (as shown in Figure 1). TESTRESET Figure 1 REMINDER: Keep your dated proof 322700-013 3/06 © 2006 Aqua Pro Systems Operating Instructions and Replacement Parts List General Safety Information (Continued) Where a 2-prong wall receptacle is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in accordance with the NEC and local codes and ordinances. 12. All wiring should be performed by a qualified electrician. 13. It is strongly recommended that this unit is plugged into a Ground Fault Circuit Interrupter (GFCI). Consult a local electrician for installation and availability (See Figure 1). ! WARNING The pump motor is equipped with an automatic resetting thermal protector and may restart unexpectedly. Protector tripping is an indication of motor overloading as a result of operating the pump at low head (low discharge restriction), excessively high or low voltage, inadequate wiring, incorrect motor conditions, or a defective motor or pump. 14. Protect electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Replace or repair damaged or worn cords immediately. Use wire of adequate size to minimize voltage drop at the motor. 15. Do not handle a pump or pump motor with wet hands or when standing on a wet or damp surface, or in water. ! DANGER If your basement or room has water or moisture on the floor, do not walk on wet area until all power has been turned off. If the shut-off box is in basement, call the electric company to shut-off service to the house, or call your local fire department for instruction. Failure to follow this warning can result in fatal electrical shock. Installation IMPORTANT: This pump is not designed for use in septic tanks or underground vaults to handle raw sewage or effluents. It should never be used in hazardous or explosive locations. Do not use power cord to lift motor. Always use the handle. 1. Pump should be located and should rest on a level solid foundation. Two inches of water is recommended to properly prime utility pump. Do not suspend pump by means of the discharge pipe or power cord. Keep pump inlet screen clear. Do not install pump directly on clay, earth or sand surfaces. Protect pump from extreme heat and cold. Use pipe joint sealant to ensure airtight pipe connections 2. Thread discharge (outlet) pipe into pump body carefully to avoid stripping or cross threading. 3. To install garden hose, install the elbow adapter provided with the pump. The elbow adapter uses a o-ring seal to provide better water removal. Rotate the elbow adapter until the o-ring seals against the pump body and the discharge is in the desired direction. Thread garden hose onto the elbow fitting. NOTE: The garden hose must be 3/4" or larger to keep friction as low as possible. A 1-1/4" sump discharge hose adapter can be connected directly to the pump body using Teflon® tape. 4. Run discharge pipe/hose away from the pump. 5. It is strongly recommended that this pump motor be electrically connected to a ground fault interrupter. Consult your local electrician for availability and installation. Power Supply: Pump is designed ...