Stimmen - 5, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
• All safety information must be followed as provided in the Service Manual. • Refer to the appropriate Parts Catalog for part number information. • Models listed on page 3. RT6212006r10 December 2011 Copyright © 2007-2011 Goodman Manufacturing Company, L.P. ® TECHNICAL MANUAL This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does not assume any responsibility for property damage or personal injury due to improper service procedures or services performed by an unqualified person. PRODUCT IDENTIFICATION The model number is used for positive identification of component parts used in manufacturing. Please use this number when requesting service or parts information. G S Z 13 024 1 A A PRODUCT FAMILY: S: Split System PRODUCT TYPE: C: Condenser R-22 X: Condenser R-410A H: Heat Pump R-22 Z: Heat Pump R-410A SEER: SEER Rating BRAND: G: Goodman® Brand (Standard Feature Set Model) S: Goodman® Deluxe V: Value NOMINAL CAPACITY 018: 1.5 Tons 024: 2 Tons 030: 2.5 tons 036: 3 Tons 042: 3.5 Tons 048: 4 Tons 060: 5 tons ELECTRICAL: 1: 208-230v 1ph/60Hz 3: 208-230v 3ph/60Hz 4: 460v 3ph/60Hz MAJOR REVISION: A: Initial Release MINOR REVISION: A: Initial Release ARNIW WW ARNING NGNG HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury or death. Goodman will not be responsible for any injury or property damage arising from improper service or service procedures. If you install or perform service on this unit, you assume responsibility for any personal injury or property damage which may result. Many jurisdictions require a license to install or service heating and air conditioning equipment. ARNIW WW ARNING NGNG Installation and repair of this unit should be performed ONLY by individuals meeting (at a minimum) the requirements of an "entry level technician", as specified by the Air-Conditioning, Heating, and Refrigeration Institute (AHRI). Attempting to install or repair this unit without such background may result in product damage, personal injury or death. ARNIW WW ARNING NGNG PRODUCT IDENTIFICATION The model number is used for positive identification of component parts used in manufacturing. Please use this number when requesting service or parts information. GSZ130181A* GSZ130241A* GSZ130301A* GSZ130361A* GSZ130421A* GSZ130481A* GSZ130601A* GSZ130241B* GSZ130361B* GSZ130363A* GSZ130483A* GSZ130484A* GSZ130603A* GSZ130604A* VSZ130181A* VSZ130241A* VSZ130301A* VSZ130361A* VSZ130421A* VSZ130481A* VSZ130601A* VSZ130241B* VSZ130361B* * Indicates minor revision & is not used for order entry or inventory management WARNINGWARNING The United States Environmental Protection Agency (“EPA”) has issued various regulations regarding the introduction and disposal of refrigerants introduced into this unit. Failure to follow these regulations may harm the environment and can lead to the imposition of substantial fines. These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office. WARNINGWARNING Do not connect or use any device that is not design certified by Goodman for use with this unit. Serious property damage, personal injury, reduced unit performance and/or hazardous conditions may result from the use of such non-approved devices. WARNINGWARNING To prevent the risk of property damage, personal injury, or death, do not store combustible materi als or use gasoline or other flammable liquids or vapors in the vicinity of this appliance. PRODUCT DESIGN 4 GSZ/VSZ13 models are available in 1 1/2 through 5 ton sizes and use R-410A refrigerant. They are designed for 208/230 volt single phase applications. Select GSZ13 models are available in 208/230 and 460 volt 3-phase applications. These models use R-410A refrigerant. The condenser air is pulled through the condenser coil by a direct drive propeller fan. This condenser air is then discharged out of the top of the cabinet. These units are designed for free air discharge, so no additional resistance like duct work shall be attached. The suction and liquid line connections on present models are of the sweat type for field piping with refrigerant type copper. Front seating valves are factory installed to accept the field run copper. The total refrigerant charge for a normal installation is factory installed in the condensing unit. GSZ units are charged for the matching evaporator coil and a 15 foot refrigerant line set. Systems should be properly sized by heat gain and loss calculations made according to methods of the Air Conditioning Contractors Association (ACCA) or equivalent. It is the contractors responsibility to ensure the system has adequate capacity to heat or cool the conditioned space. GSZ/VSZ models use high-efficiency Copeland® scroll "Ultratech" compressors which are specifically desgined for R-410A refrigerant. There are a number of design characteristics which are different fro...