Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Graco Dateigröße: 2.35 mb Dateiname: 307932r.pdf Unterrichtssprache:

245187, 33:1, Series B 3300 psi (22.8 MPa, 228 bar) Maximum Fluid Working Pressure 100 psi (700 kPa, 7 bar) Maximum Air Input Pressure Part No. 253697, 28:1, Series A 2800 psi (19.3 MPa, 193 bar) Maximum Fluid Working Pressure 100 psi (700 kPa, 7 bar) Maximum Air Input Pressure Part No. 245185, Series B (240 Volt Heater) Part No. 245186, Series B (480 Volt Heater) For heated spray applications. 3000 psi (20.7 MPa, 207 bar) Maximum Fluid Working Pressure 90 psi (600 kPa, 6 bar) Maximum Air Input Pressure GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 Copyright 1998, Graco Inc. is registered to I.S. EN ISO 9001 307932R Model 245187 Shown 4414B Instructions Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 2 for Table of Contents. GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 Copyright 1998, Graco Inc. is registered to I.S. EN ISO 9001 307932R Model 245187 Shown 4414B Instructions Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 2 for Table of Contents. Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operation/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 14 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . 22 Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Symbols Warning Symbol WARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions. WARNING INSTRUCTIONS EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. . This equipment is for professional use only. . Read all instruction manuals, tags, and labels before operating the equipment. . Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor. . Do not alter or modify this equipment. . Check equipment daily. Repair or replace worn or damaged parts immediately. . Do not exceed the maximum working pressure of the lowest rated system component. Refer to the Technical Data on page 21 for the maximum working pressure of this equipment. . Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings. . Do not use hoses to pull equipment. . Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 180F (82C) or below –40F (–40C). . Wear hearing protection when operating this equipment. . Do not lift pressurized equipment. . Comply with all applicable local, state, and national fire, electrical, and safety regulations. 2 307932 WARNING SKIN INJECTION HAZARD Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury. . Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment. . Do not point the gun at anyone or at any part of the body. . Do not put your hand or fingers over the spray tip. . Do not stop or deflect leaks with your hand, body, glove or rag. . Do not “blow back” fluid; this is not an air spray system. . Always have the tip guard and the trigger guard on the gun when spraying. . Check the gun diffuser operation weekly. Refer to the gun manual. . Be sure the gun trigger safety operates before spraying. . Lock the gun trigger safety when you stop spraying. . Follow the Pressure Relief Procedure on page 14 if the spray tip clogs and before cleaning, checking or servicing the equipment. . Tighten all fluid connections before operating the equipment. . Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not repair high pressure couplings; you must replace the entire hose. . Use only Graco approved hoses. Do not remove the spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. MOVING PARTS HAZARD Moving parts, such as the air motor piston, can pinch or amputate your fingers. . Keep clear of all moving parts when starting or operating the pump. . Before servicing the equipment, follow the Pressure Relief Procedure on page 14 to prevent the equipment from starting...

Herunterladen

Geben Sie zwei Ziffern: