Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
READ AND FOLLOW ALL INSTRUCTIONS. 2. WARNING : To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. 3. CAUTION: This pump is for use with permanently installed pools and may also be used with hot tubs and spas if so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it may be readily disassembled for storage and reassembled to its original integrity and has a maximum dimension of 18 ft. (5.49m) and a maximum wall height of 42 in. (1.07m). 4. Do not install within an outer enclosure or beneath the skirt of a hot tub or spa unless so marked. 5. SAVE THESE INSTRUCTIONS. 05/04 1 97490010 INSTALLATION & OPERATING INSTRUCTIONS GENERAL Your AQUA-FLO pump has been quality built and engineered to give maximum efficiency under normal water pumping conditions. Consult the manufacturer for any other applications. LOCATION OF PUMP For best pump performance, locate the system as close to the water source as possible. Provide adequate access around the pump for inspection and maintenance. Place pump on a firm level surface. Pump need not be bolted down unless required by local code. PUMP CONNECTIONS Suction line from pool (skimmer and main drain) must be connected to inlet at hair and lint trap. Discharge line to pool (return lines) must be connected to outlet at top of pump via filter. If pump is installed below water level of pool, install valves on the inlet and outlet piping to permit removing of equipment without draining the pool. CAUTION: During the pressure test procedure, this pump is under pressure. DO NOT LOOSEN lock handles while pump is running or until all pressure is released. Tighten lock handles securely by hand only. Raise pressure slowly. Do not exceed 50 psi. Extreme care must be taken during pressure test. Failure to follow these instructions explicitly can result in personal injury. PRIMING PUMP At initial start-up, pump must be primed by filling hair and lint trap with water. To prime pump, remove cover from hair and lint trap: fill pump and suction trap with water. Replace cover (make sure the o-ring is in place) and tighten lock handles. Pump will now prime, with priming time depending upon lift and horizontal distance of suction piping. CAUTION: Do not remove hair and lint strainer lid while pump is running or under pressure! Lid is held in place by lock handles which can be removed or tightened by hand. Basket must be kept clear of leaves and debris at all times. REMOVING BASKET 1.) Turn off motor. 2.) Remove lid. 3.) Remove basket and empty debris. 4.) Replace basket, fill with water, replace lid securely to prevent air from entering and tighten. DO NOT USE TOOLS. 5.) Turn on motor. 6.) Open air-relief valve on top of filter until steady stream of water comes out. NOTE: If pump is installed below water level of pool, close return and suction lines prior to opening hair and lint pot. Make sure to re-open valves prior to operating. DO NOT RUN PUMP DRY! Always maintain proper water level in pool. If water level falls below skimmer intake, pump will suck air. Pump is equipped with a maintenance-free, heavy- duty mechanical seal. Damage will occur if pump runs dry, and warranty will be voided. TO PREVENT FREEZING Drain liquid from pump through plug at bottom section of volute. It is recommended to apply a good rust inhibitor into liquid end to prevent corrosion. Text Box: 2 Be sure motor is kept dry and covered. In mild climate area, when freezing may occur, run pump and filter equipment continuously to prevent freezing. MOTOR Your pump is equipped with a permanently lubricated, maintenance-free, heavy- duty industrial quality motor especially designed to withstand the heavy-duty requirements of swimming pool application. Wiring connection must agree with incoming line voltage. Improper wiring can cause serious injuries and damage to the motor, voiding warranty. NOTE: Your motor is designed to withstand the effects of normal rainfall. To increase the life of your motor, observe the following: 1.) Do not flood motor or submerge in water. To do so voids warranty. 2.) Provide ample cross ventilation, minimum of 6” at all points. 3.) Keep motor and surrounding area clean. 4.) Avoid sweeping or stirring dust near motor while it is running. 5.) Avoid storing or spilling dry chemicals, powders, etc., near motor. 6.) Provide protection against the elements. 7.) Locate motor on a slight elevation so water will drain away from motor. 8.) Avoid spilling or dripping liquid chemical on or near motor. 9.) Avoid splashing water or hosing deck near motor. Water damage voids warranty. For replacements, contact your local supplier or authorized service center. WARNING - All electrical wiring of the motor installation must be done by a qualified electrician in accordance with applicable ...