Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
SERIES PUMPS WITH “ENVIRO-HEAT” TECHNOLOGY. Congratulations! The spa bath you have selected is one of the finest available! One of the many qualities that made this spa bath the best - is the use of Aqua-Flo’s Therma-Flo. pump with Enviro-Heat Technology. The Therma-Flo. EHT pump was designed with you, the user, in mind…to provide you with the highest performance at a much lower operating cost, as compared to any other pump in its class. The Therma-Flo. EHT pump does not utilize traditional power hungry heaters to heat-up or maintain the temperature of water in your spa bath; rather, it recovers the heat generated during the transition of electrical energy to mechanical energy. Through this innovative method, the Therma-Flo. EHT pump does not use additional energy to heat up the water, making this the most energy efficient and environmentally friendly pump available. By making this intelligent purchase decision, you will save money and you have helped the environment. More About Aqua-Flo… Aqua-Flo is the leading supplier of pumps to the Leisure Water Industry, serving the portable spa, jetted bath and swimming pool industries since 1971. Headquartered in Chino, California, U.S.A., Aqua-Flo has manufactured and sold millions of pumps worldwide from our state-of-the-art manufacturing facility. Our skilled and experienced associates utilize the best computer design and simulation softwares for original product development. We, at Aqua-Flo, pride ourselves on our high quality, reliable & innovative products; while providing unparalleled customer service. We are committed to provide you with the most pleasant and hassle free experience - guaranteed. IMPORTANT: This pump is intended for spa bath use ONLY, and is not suitable for any other application. 05/04 Page 1 97492000 INSTALLATION & OPERATING INSTRUCTIONS Therma-Flo. Series Pumps MOUNTING PREPARATION 1. Find a suitable indoors mounting location where the pump is close to the spa bath, as safely as possible, but remains inaccessible to the person in the spa bath. a. The pump’s suction port (inlet) must be lower than the normal operating bath water level to ensure proper pump priming, but higher than the spa bath suction to ensure correct draining. When emptied, the water must drain back into the spa bath as required by Health Department Regulations. b. The discharge port (outlet) should be lower than the water level and the plumbing should be horizontal or rise slightly to prevent airlocks. Airlocks will prevent the pump from properly priming. To Bath’s Suction To Bath’s Jet 2. This pump is intended for permanent installation only and must not be used in portable service application. The mounting surface must be constructed from durable material and supported securely in a horizontal position. 3. A clearance of at least 7.5 cm (3”) on all sides (top, sides, front, and back) is required for ease of installation and air circulation. Enclosures must be adequately ventilated to promote free flow of air and prevent condensation. 4. Provision for securing the plumbing leading to the pump must be considered to avoid undue stress to the pump’s connections. 5. The pump requires 220-240 Volts A.C., 10 amperes minimum, 50 Hz, single-phase power supply supplied through a Residual Current Device (RCD) with a rated tripping current not exceeding 30 mA. Above are the minimum requirements required for installing this pump. Additional requirements, standards, and codes, mandated by government agencies on specific areas where the pump will be installed, must be followed. 2 WARNINGS (may cause serious injuries or death) • The power supply must be turned off during the installation process. • This pump is wired for 220-240 VAC, 50 Hz, and Single Phase power supply only. The power supply should be supplied through a Residual Current Device (RCD) with a rated tripping current not exceeding 30 mA. • No part of the pump is to be located above the spa bath during use. Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa bath. • Pump and other parts containing energized or live parts, except parts supplied with safety extra low voltage not exceeding 12 V, must be INACCESSIBLE to a person in the spa bath. • Pump must be mounted on top of a horizontal and solid surface; fixed securely using screws or bolts through the 4 mounting holes located on the base. • The appliance is not intended for use by young children or infirm persons without supervision. • Young children should be supervised to ensure that they do not play with the appliance. CAUTION (may cause property damage) • This pump is intended for Spa Bath use ONLY, and is not suitable for any other application. • The pump is NOT self-priming; therefore, the water fill-level of the spa bath must be equal or higher than the pumps suction port (inlet). • DO NOT run the pump without water. This may damage pump and its components. • DO NOT open or servic...