Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Intex Recreation
Dateigröße: 1.02 mb
Dateiname: cb3f7ad3-75d9-43de-bfa1-cfd5c56e89f4.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
. May not reflect actual product. Not to scale. 7 8 (58) MODEL 604 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/19/2007 SAVE THESE INSTRUCTIONS Page 5 PPAARRTTSS RREEFFEERREENNCCEE 58 PARTS REFERENCE Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts. When ordering parts, be sure to quote the model number and part numbers. 1 2 3 4 5 6 7 8 9 REF. NO. DESCRIPTION QTY. SPARE PART NO. 1 1 1 1 1 2 2 4 2 AIR RELEASE VALVE VALVE O-RING THREADED COVER COVER SEAL FILTER CARTRIDGE (59900) STRAINER HOSE HOSE CLAMP HOSE SEAL 10460 10264 10459 10325 10120 10399 10122 10134 NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale. 7 6 8 9 1 2 3 4 5 58 SAVE THESE INSTRUCTIONS Page 6 SSEETT-- UUPP IINNSSTTRRUUCCTTIIOONNSSSET-UP INSTRUCTIONS Be sure you have access to water to fill the pool and chemicals for the water. A small coin can be used to tighten the hose clamps (8). IMPORTANT: This filter pump is shipped with the air release valve (1) open (open the air release valve if necessary). DO NOT replace the air release valve until you reach STEP #8. Failure to follow these instructions will result in air trapped inside filter housing; the motor will run dry, be noisy and malfunction. 1. Assemble above-ground-pool first. Carefully follow the pool’s installation instructions. 2. Place the Filter-Pump the length of the hose away from the pool wall where the lower black protruding hose connection is "sticking-out". 3. Remove wall plugs and then insert the strainers (6) into each of the protruding hose connections. The hoses (7) fit over the strainers inserted into the connections. 4. There are two hoses to be connected to the Filter-Pump hose connections. With hose clamps (8), fasten one of the hoses (7) to the lower protruding hose connection (marked "+" on the pool liner) and to the pump connection (marked "+"). 5. Connect the second hose to the remaining upper protruding hose connection and to the lower pump connection. Make sure all the hose clamps (8) are tight. 6. Twist the Filter-Pump’s threaded cover (3) in a clock-wise direction to be sure it is on "tight". Use only your hands to tighten the top. Do not tighten with tools such as pliers. 7. Fill the pool to a level of at least 1-2 inches above the top connection. The water will automatically flow down into the pump. 8. When water starts flowing out of the air release valve hole, screw in the air release valve back into the filter housing cover. Do not over tighten the valve. NOTE: Venting the system is necessary for air to escape as the filter housing fills with water. 9. Connect the filter pump to the power outlet. The filter pump is now filtering the water. 10. Operate the filter pump until the desired water clarity is obtained. (58) MODEL 604 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/19/2007 WARNING Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a portable residual current device (PRCD). (58) MODEL 604 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/19/2007 58 SAVE THESE INSTRUCTIONS Page 7 SSEETT-- UUPP IINNSSTTRRUUCCTTIIOONNSSSET-UP INSTRUCTIONS (continued) WARNING Position this product away from pool to prevent a child from climbing the pool. To inspect and change the filter cartridge, disconnect line cord, unscrew the strainer grids (6) from the strainer connectors and insert the hat-like plugs into the strainer connectors before servicing the filter. After service, open the air release valve, remove the plugs, allow any air to escape through the valve before tightening the valve again and replace the strainer grids. The pump is now primed with water again and may be turned on. (ILLUSTRATION NOT TO SCALE) WATER LEVEL HOSE CLAMP INSIDE OF POOL STRAINER PLUG UPPER PROTRUDING HOSE CONNECTION WATERDIRECTION WATERDIRECTION UPPER PUMP CONNECTION BOTTOM PUMP CONNECTION THREADED COVER FILTER CARTRIDGE INSIDE AIR RELEASE VALVE HOSE (58) MODEL 604 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/19/2007 58 SAVE THESE INSTRUCTIONS Page 8 SSTTAATTIIOONNAARRYY MMOOUUNNTTIINNGG OOPPTTIIOONNFILTER PUMP STATIONARY MOUNTING OPTION -- (3) x M6 HEXAGON HEAD BOLTS -- (3) x M6 HEXAGON LOCK-NUTS 135mm 135mm 135mm 135mm 135mm135mm There are three mounting holes located at the bottom of the filter-pump base. These holes are provided because various country’s regulations, especially in the European community, require the filter-pump to be secured to the ground or to a base in a permanent upright position. These three holes form a triangle pattern and are 135mm from each other. The holes are slotted with a 7mm width. The filter-pump can be mounted on a cemen...