Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: HP Dateigröße: 44.86 kb Dateiname: Unterrichtssprache:

For use with nonflammable, non-abrasive liquids compatible with pump component materials. Figure 1 - Dimensions CP Y Suction E E HL D X S F Discharge Dimensions (Inches) Model Suc.* Dis.* CP† D E F H L S X Y 5660-97 1" 1" 14.11 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5661-97 1 1 14.61 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5662-97 1 1 15.11 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5664-97 1 1 16.09 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5665-97 1 1 15.53 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5666-97 1 1 16.03 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5667-97 1 1 16.41 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 5669-97 1 1 17.66 3.50 2.25 3.00 0.44 4.28 4.00 5.25 3.94 (*) Standard NPT (female) pipe thread. (†) This dimension may vary due to motor manufacturer’s specifications. 5660-250-00 09/2002 Specifications Information and Repair Parts Manual 5660-97 thru 5669-97 1-Inch Self-Priming Centrifugal Pumps Low Volume Liquid Transfer Bronze Specifications seat to avoid scratching seal seat. DRIVER PUMP Ship Power NEMA Weight Model HP Phase Enclosure Supply Hertz Frame RPM Casing Adapt. Imp. Seals‡ (Lbs.) 5660-97 1/2 1 ODP 115/230 VAC 60 56J 3450 BR BR BR Buna N 38 5661-97 3/4 1 ODP 115/230 VAC 60 56J 3450 BR BR BR Buna N 39 5662-97 1 1 ODP 115/230 VAC 60 56J 3450 BR BR BR Buna N 42 5664-97 2 1 ODP 115/230 VAC 60 56J 3450 BR BR BR Buna N 60 5665-97 1/2 1 TEFC 115/230 VAC 60 56J 3450 BR BR BR Buna N 41 5666-97 3/4 1 TEFC 115/230 VAC 60 56J 3450 BR BR BR Buna N 43 5667-97 1 1 TEFC 115/230 VAC 60 56J 3450 BR BR BR Buna N 46 5669-97 2 1 TEFC 115/230 VAC 60 56J 3450 BR BR BR Buna N 65 (ODP) Open Drip Proof; (TEFC) Totally Enclosed Fan Cooled; (BR) Bronze (‡) Shaft seal also contains carbon, ceramic, and stainless steel components. NOTE: Driver data is subject to change without notice, see label on driver for actual specifications. Performance GPM of Water at Total Head in Feet Max. Model HP 10' 20' 30' 40' 50' 60' Head** 5660-97, 5665-97 1/2 38 30 20 9 — — 47 ft. 5661-97, 5666-97 3/4 56 48 37 24 7 — 53 5662-97, 5667-97 1 70 61 50 38 24 — 60 5664-97, 5669-97 2 90 83 74 64 50 28 68 (**) Shutoff; to convert to PSI, multiply by SG (specific gravity of liquid), then divide by 2.31. Figure 2 - Mechanical Seal Replacement Impeller Motor shaft Adapter Seal headSeal seat 4. Unthread fasteners (Ref. No. 6) and (This is a lapped surface and must be remove motor adapter (Ref. No. 4). handled very carefully.) Seal head and impeller shims (Ref. 10. After seal seat is in place, insure that No. 11) will come loose at this time. it is clean and has not been marred. 2 Specifications Information and Repair Parts Manual Models 5660-97 thru 5669-97 Maintenance (Continued) 11. Using a clean cloth, wipe shaft and make certain that it is perfectly clean. NOTE: If removed, slide slinger washer (Ref. No. 2) onto shaft until it is located approximately 1/8" from face of motor bearing hub. 12. Carefully guide motor shaft through seal seat. Secure motor adapter on motor mounting face. 1...

Herunterladen

Geben Sie zwei Ziffern: