Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Central Pneumatic Dateigröße: 1.09 mb Dateiname: Unterrichtssprache:

Once completed, it is not necessary to repeat.) 1. Do not attach a hose or any other fitting to the compressor. 2. Turn on/off switch to OFF position. 3. Plug in power cord. 4. Turn on/off switch to ON position. Allow compressor to run for 5 minutes. 5. Turn on/off switch to OFF position. 6. Unplug power cord. BEFORE EACH STARTUP OPERATING PROCEDURE 1. Connect air hose to open port located below pressure gauge. 2. Attach the necessary fitting or tool to open end of air hose. 3. Turn on/off switch to OFF position. 4. Plug in power cord. 5a. If using inflation needles/nozzles: Attach air hose with inflation fitting to the object you are going Handle Pressure Gauge Safety Valve to inflate. While holding inflation fitting firmly in place, turn on/off switch to ON position. Allow compressor to inflate the object. Turn off compressor and remove inflation fitting. 5b. If using tire chuck or tool: Once chuck or tool is attached to air hose, turn on/off switch to ON position and allow compressor to run until it automatically shuts off. When using tire chuck to inflate tires, observe gauge reading on compressor and periodically check tire pressure with a separate tire gauge to prevent overinflation. On/Off cycling of compressor In the ON position, the compressor pumps air into the tank. When a shutoff (preset “cut-out”) pressure is reached, the compressor automatically shuts off. If the compressor is left in the ON position and air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically at its preset “cut-in” pressure. When a tool is being used Extension cords for 120V/2.5 Amp Unit Length of Cord (ft) 25 50 100 150 200 250 300 400 500 Gauge of Cord 18 18 16 14 14 12 12 10 10 3 Oilless Compressors Operation (Continued) continuously, the compressor will cycle on and off automatically. In the OFF position, the pressure switch cannot function and the compressor will not operate. Make sure switch is in OFF position when connecting or disconnecting power cord from electrical outlet. ASME SAFETY VALVE Do not remove or attempt to adjust the safety valve! Check the safety valve by performing the following steps: 1. Plug the compressor in and run until shut off pressure is reached (see Operating Procedure). 2. Wearing safety glasses, pull the ring on the safety valve to release pressure from compressor tank. Use your other hand to deflect fast-moving air from being directed toward your face. 3. The safety valve should automatically close at approximately 40-50 psi. If the safety valve does not allow air to be released when you pull on the ring, or if it does not close automatically, it MUST be replaced. Maintenance Disconnect power source then release all pressure from the system before attempting to install, service, relocate or perform any maintenance. Check compressor often for any visible problems and follow maintenance procedures each time compressor is used. Safety MOISTURE IN COMPRESSED AIR Moisture in compressed air will form into droplets as it comes from an air compressor pump. When humidity is high or when a compressor is in continuous use for an extended period of time, this moisture will collect in the tank. When using a paint spray or sandblast gun, this water will be carried from the tank through the hose, and out of the gun as droplets mixed with the spray material. IMPORTANT: This condensation will cause water spots in a paint job, especially when spraying other than water based paints. If sandblasting, it will cause the sand to cake and clog the gun, rendering it ineffective. A filter in the air line (MP3105), located as near to the gun as possible, will help eliminate this moisture. valve must be replaced if it cannot be actuated or it leaks air after ring is released. 1. Turn compressor off and release pressure from system. (To release pressure from system, pull ring on ASME safety valve. Deflect escaping air by shielding valve with one hand as you pull ring with other hand.) Pull ring until tank is empty. A large amount of fast moving air will be released when the safety valve is opened with pressure in the tank. Wear ANSI a...

Herunterladen

Geben Sie zwei Ziffern: