Stimmen - 0, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4. Reinstall the air cleaner element and cover. AIR CLEANER ELEMENT AIR CLEANER COVER 3. 3. Recommended spark plug: BPRGES(NGK) W2OEPR-U(NlPPONDENS0) To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful not to touch the muffler while it is hot. 2. Visually inspect the spark plug. Discard it if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused. 3. Measure the plug gap with a feeler gauge. Correct as necessary by bending the side electrode. The gap should be: 0.70-0.80 mm (0.028-0.031 in) 0.7-0.8 mm (0.028-0.031 in) 4.Check that the spark plug washer is in good condition, and thread the spark plug in by hand to prevent cross-threading. 4.Check that the spark plug washer is in good condition, and thread the spark plug in by hand to prevent cross-threading. - If installing a new spark plug, tighten l/2 turn after the spark plug seats to compress the washer. - If reinstalling a used spark plug, tighten l/8-l/4 turn after the spark plug seats to compress the washer. l The spark plug must be securely tightened. An improperly tightened spark plug can become very hot and may cause engine damage. l• Use only the recommended spark plug or equivalent. A spark plug which has an improper heat range may cause engine damage. 4.Spark arrester maintenance (optional part) 4.Spark arrester maintenance (optional part) 1. Remove the two 8 mm nuts, and remove the muffler. 2.Remove the two 4 mm screws, and remove the deflector from the muffler protector. 3.Remove the four 5 mm self-tapping screws, and remove the muffler protector from the muffler. 4.Remove the 4 mm screw, and remove the spark arrester from the muffler. 5 mm SELF-TAPPING PROTECTOR 4 mm SCREWS 4 mm SCREW SPARK ARRESTER Be careful not to damage the spark arrester screen. It must be free of breaks and holes. Replace if necessary. 5. Use a brush to clean carbon deposits from the spark arrester screen. 6. Inspect the spark arrester. 7. Install the spark disassembly. arrester and the muffler in the reverse order of 8.TRANSPORTlNGlSTORAGE 8.TRANSPORTlNGlSTORAGE Contact with a hot engine or exhaust system can cause serious burns or fires. Let the engine cool before transporting or storing the water pump. Before storing the pump for an extended period; 1. Be sure the storage area is free of excessive humidity and dust. 2. Clean the pump interior. Sediment will settle in the pump if it has been used in muddy or sandy water, or water containing heavy debris. Pump clean water through the pump before shutting down or the impeller may be damaged when restar- ting. After flushing, remove the pump drain plug, and drain as much water as possible from the pump housing. After the pump is dry, spray Honda Rust Penetrant into the pump housing through the suction port, discharge port, and drain hole, then reinstall the drain plug. PUMP DRAIN PL 3. 3. a. With the fuel valve OFF, remove the carburetor drain screw. b. Drain the gasoline from the carburetor into a suitable container. c. If the tank is to be drained, turn the fuel valve ON and drain the fuel in the tank into a suitable container. d. Reinstall the drain screw and turn the fuel valve OFF. Gasoline is extremely flammable and is explosive under certain conditions. Perform this task in a well ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area during this procedure. SCREW STORAGE TIME RECOMMENDED SERVICE PROCEDURE TO PREVENT HARD STARTING Less than 1 month No preparation required 1 to 2 months Fill with fresh gasoline and add gasoline conditioner*. Fill with fresh gasoline and add gasoline 2 months to 1 year conditioner*. Drain the carburetor float bowl. Fill with fresh gasoline and add gasoline conditioner*. 1 year or more Drain the carburetor float bowl. After removal from storage, drain the stored gasoline into a suitable container, and fill with fresh gasoline before starting. * Use gasoline conditioners that are formulated to extend storage life. Contact your authorized Honda water pump dealer for recommen- dations of gasoline conditioners. 4. 4. 5. Remove the spark plug and pour about a tablespoon of clean engine oil into the cylinder. Crank the engine several revolutions to distribute the oil,then reinstall the spark plug. 6. Pull the starter rope slowly until resistance is felt. Continue pulling until the notch on the starter pulley aligns with the hole on the recoil starter (see illustration below). At this point,the intake and exhaust valves are closed. This will help to protect the engine from internal corrosion. Align the mark on the starter pulley with the hole at the top of recoil starter. 7. Check the air cleaner and clean as necessary (see page 18). 8. Cover the engine and pump to keep out dust. When the engine will not start: When the engine will no...