Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Briggs & Stratton Dateigröße: 595.03 kb Dateiname: Unterrichtssprache:

. . . . . . . . . . . . . . . 28.42 cu. in. (465.7 cc) Note: For practical operation, the horsepower loading should not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6° C) above 77° F (25° C). Engine will operate satisfactorily at an angle up to 15°. TUNE-UP SPECIFICATIONS Armature air gap . . . 0.010 – 0.014 in. (0.25 – 0.36 mm) Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm) Valve clearance with valve springs installed and piston 1/4 in. (6 mm) past top dead center (check when engine is cold). See Repair Manual P/N 270962. Model 190000 intake . . . . . .005 – .007 in. (.13 – .18 mm) Model 190000 exhaust . . . .007 – .009 in. (.18 – .23 mm) Model 280000 intake . . . . . .005 – .007 in. (.13 – .18 mm) Model 280000 exhaust . . . .009 – .011 in. (.23 – .28 mm) THE INTERNATIONAL SYMBOLS USED ON THE ENGINE OR IN THIS MANUAL INCLUDE: On Off Fuel Shutoff Read Owner’s Manual Stop Choke Fuel Safety Alert Oil CAUTION: This engine is shipped from Briggs & Stratton without oil. Check oil level before starting engine. If you start the engine without oil, the engine will be damaged beyond repair and will not be covered under warranty. OIL CAPACITY Engine Model Series 190000 holds about 1-1/8 qts (36 ozs or 1.1 ltrs). Engine Model Series 280000 holds about 1-1/2 qts (48 ozs or 1.4 ltrs). TYPE OF OIL TO USE • Use a high quality detergent oil classified “For Service SF, SG, SH, SJ” or higher, such as Briggs & Stratton 30W, Part Number 100005 (20 oz) or 100028 (48 oz). • Do not use special additives. • Choose a viscosity according to the table opposite. Note: Synthetic oil meeting ILSAC GF-2, API certification mark and API service symbol (shown at left) with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil at all temperatures. Use of synthetic oil does not alter required oil change intervals. OIL °F -20 0 20 40 60 80 100 °C -30 -20 -10 0 10 20 30 40 STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE * ** 32 * CAUTION: Air cooled engines run hotter than automotive engines. The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.) in temperatures above 40° F (4° C) will result in higher than normal oil consumption. When using a multi-viscosity oil, check oil level more frequently. ** CAUTION: SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to inadequate lubrication. SAE Viscosity Grades CHECKING AND ADDING OIL • Check oil level before starting the engine. • Keep oil level at FULL. • Check level daily, or after every eight (8) hours. • Do not overfill. [1] Place engine level and clean around oil fill area. Oil Fill [2] Remove dipstick and wipe clean with cloth. [3] Replace and tighten dipstick. Remove and check oil level. [4] Oil level should be at FULL mark on dipstick. [5] If needed, add oil slowly recheck. Do not over fill. [6] Replace and tighten dipstick. 7 FUEL TYPE OF FUEL TO USE • Use clean, fresh, regular unleaded gasoline with a minimum of 77 octane. Fresh fuel prevents gum from forming in the fuel system or on essential carburetor parts. Purchase fuel in quantity that can be used within 30 days. • Do not u...

Herunterladen

Geben Sie zwei Ziffern: