Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
You can configure the thermostat for use with either multi-stage electric heat systems or multi-stage gas systems. When configured for electric heat, the G terminal (blower/fan) will be energized on a call for heat. This thermostat is designed to operate a single-transformer system. If you have a two- transformer system, cut and tape off one transformer. If transformer safety circuits are in only one of the systems, remove the transformer of the system with NO safety circuits. If required, replace remaining transformer with a 75VA Class II transformer. After disconnecting one transformer, the two commons must be jumpered together. Use the terminal output information below to help you wire the thermostat properly for your multi-stage system. After wiring, see CONFIGURATION section for proper thermostat configuration. THERMOSTAT TERMINALS (Upper) L PH D SA SB SC OT Malfunction Light X-10 Module Input Not Used Remote Sense A Remote Sense B Remote Sense C Outdoor Sensor THERMOSTAT TERMINALS (Lower) SYSTEM E C R W3/A1 W2 E2/P W1 Y2 Y1 B O G Multi-Stage No Function 24 Volt (Common) 24 Volt (Hot) Damper terminal energized in occupied mode Heat mode 2nd stage No function Heat mode 1st stage Cool mode 2nd stage Cool mode 1st stage Energized in Heat and Off Mode Energized in Cool Mode Blower/Fan Energized on call for Cool (and Heat if confgured to Electric Heat). HEAT PUMP TERMINAL OUTPUTS Refer to equipment manufacturers’ instructions for specific system wiring information. You can configure the thermostat for use with the following heat pump system types: HEAT PUMP TYPE 1. Single-stage compressor system; gas or electric backup. HEAT PUMP TYPE 2. Multi-stage or two- compressor system; gas or electric backup. HEAT PUMP TYPE 3. System requiring separate signals for heat (W1, W2) and cool (Y1); gas or electric backup. This thermostat is designed to operate a Use the terminal output information below to single-transformer system. If you have a two-help you wire the thermostat properly for transformer system, cut and tape off one your heat pump system type. After wiring, transformer. If transformer safety circuits are see CONFIGURATION section for proper in only one of the systems, remove the thermostat configuration. transformer of the system with NO safety circuits. If required, replace remaining transformer with a 75VA Class II transformer. After disconnecting one transformer, the two commons must be jumpered together. THERMOSTAT TERMINALS (Upper) L PH D SA SB SC OT Malfunction Light X-10 Module Input Not Used Remote Sense A Remote Sense B Remote Sense C Outdoor Sensor THERMOSTAT TERMINALS (Lower) SYSTEM E C R W3/A1 W2 E2/P W1 Y2 Y1 B O G Single-stage compressor system; gas or electric backup Heat Pump 1* Heat mode 1st stage. Emergency mode 1st stage. 24 Volt (Common) 24 Volt (Hot) Damper terminal energized in occupied mode Heat mode 3rd stage. Emergency mode 2nd stage E2 - Emergency mode constant output. P - All other modes constant output. Heat mode 2nd stage No Output Heat and cool modes 1st stage (compressor) Energized in Heat, Off, Emergency Mode Energized in Cool Mode Blower/Fan Energized on call for Heat and Cool Multi-stage or two compressor system; gas or electric backup Heat Pump 2* Emergency mode 1st stage 24 Volt (Common) 24 Volt (Hot) Damper terminal energized in occupied mode Emergency mode 2nd stage E2 - Emergency mode constant output. P - All other modes constant output. Heat mode 3rd stage Heat and cool modes 2nd stage (compressor 2) Heat and cool modes 1st stage (compressor 1) Energized in Heat, Off, Emergency Mode Energized in Cool Mode Blower/Fan Energized on call for Heat and Cool System requiring separate signals for heat (W1, W2) and cool (Y1); gas or electric backup Heat Pump 3** Emergency mode 1st stage 24 Volt (Common) 24 Volt (Hot) Damper terminal energized in occupied mode Heat mode 2nd stage. Emergency mode 2nd stage. E2 - Emergency mode constant output. P - All other modes constant output. Heat mode 1st stage No Output Cool mode 1st stage Energized in Heat, Off, Emergency Mode Energized in Cool Mode Blower/Fan Energized on call for Heat and Cool * If system does not provide connection to E, jumper W1 to E to provide Aux heating in emergency mode. ** If system does not provide connection to E, jumper W2 to E to provide Aux heating in emergency mode. 3 CONFIGURATION SWITCHES RESET SWITCH See the Troubleshooting section at the end of this document for more information about the function of this switch. E2/P SWITCH The E2/P switch is located on the back of the thermostat body (see fig. 2). This switch controls how the E2/P terminal of the thermostat will be energized. When the switch is in the E2 position (down), the E2/P terminal will be energized only when in emergency heat. When the switch is in the P position (up), the E2/P terminal will always be energized except when in emergency heat. Consult the equipment manufacturer or a qualified heating/cooling service person before setting this s...