Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
If there is any doubt, do not operate the Siphon Pump. 15. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. 16. Self Priming Pump. This pump is self priming. DANGER!! Attempting to prime the pump by using your mouth on the hose could result in severe illness or death. 17. Only transfer and pump gasoline in a well-ventilated area. Make sure your work area is well-ventilated and clear of any flammable materials. WARNING!! Gasoline fumes are highly flammable and subject to possible explosion. 18. Wash Pump after use. Always wash both hoses and Pump thoroughly with soap and water and then air dry before re-using the Pump and hoses. 19. Store liquids in the proper container. When transfering gasoline, only put gasoline in an approved container. Never store gasoline in a glass container. 20. Let engine cool. When transferring oil, always let the vehicle’s engine and all other components, such as oil, cool before using the Pump. When finished, clean the Pump of oil throroughly. Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Page 3 SKU 3878 Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation To Assemble: 1. Insert one end of the clear Intake Hose (2) into a black Hose Connector (5). Insert the hose with connector into the top intake valve of the Pump (1) and tighten securely. See Figure 1 Pump (1) Hose Connector (5) Intake Hose (2) Figure 1 2. Repeat Step 1 using the clear Discharge Hose (3), except insert this hose with connector into the bottom discharge valve of the Pump (1) and tighten securely. 3. To begin the siphon process, put the Intake Hose (2) into the liquid to be transferred. Put the Discharge Hose (3) into the location where the liquid is to go. Please note: Make sure that the Discharge Hose (3) is positioned lower than the Intake Hose (2). 4. Prime the Siphon Pump (1) with 3 to 4 pumps of the plunger at the top of the Pump. Once the liquid begins to flow, it will transfer without further pumping. Page 4 SKU 3878 WHEN SIPHONING GAS: Follow Steps 1-4 listed on page 4. After each use, pump out the remaining residue of gas from both the Intake Hose (2) and Discharge Hose (3). Wash thoroughly with soap and water and let air dry before storing the Pump. Please note: Many cars have a baffle (small metal flap) in their gas tank inlet to prevent a siphoning tube from being inserted. Use a screwdriver (not included) to hold open the baffle when siphoning. TO CHANGE OIL: 1. Follow Steps 1-2 and then insert the Dipstick Connector (4) into one end of the Dipstick Tube (7). Insert the Dipstick Connector (4) into the end of the Intake Hose (2). See Figure 2. Intake Hose (2) Dipstick Tube (7) Dipstick Connector (4) Figure 2 2. Insert the other end of the Dipstick Tube (7) into the engine dipstick hole until it reaches the bottom of the crankcase. Place the Discharge Hose (3) into the oil drain pan and begin to pump. TO USE AS AIR PUMP: 1. Insert the Air Pressure Hose (6) into a Hose Connector (5) and then insert both into the discharge nozzle (bottom valve on Pump). See Figure 3. Figure 3 Hose Connector (5) Air Pressure Hose (6) Pump (1) 2. Tighten securely and begin pumping. Please note: To inflate footballs, beach balls, etc., place an inflation needle in the threaded adapter on the end of the Air Pressure Hose (6) and begin pumping. Warning: Always adhere to the inflatable item’s recommended PSI rating. Over-inflating could result in damage to item or a possible explosion and result in serious injury. Page 5 SKU 3878 Maintenance 1. To clean, attach both hoses to the Pump and siphon warm, soapy water through the Pump until it comes out clean. Repeat the process with clean water to wash out the soap. 2. Wipe down the Pump and hoses with a lint free cloth. Allow to air dry and keep the unit disassembled during storage. Allow ample time for residual fumes to dissipate. Store away from heat or spark sources. Assembly Drawing and Parts List 1 5 3 4 2 6 7 8 Part # Description Qty. 1 Pump 1 2 Intake Hose 1 3 Discharge Hose 1 4 Dipstick Connector 1 5 Hose Connectors 2 6 Air Pressure Hose 1 7 Dipstick Tube 1 8 Air Nozzle 1 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EX...