Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Protect yourself and others by obeying all Safety Information. Failure to comply with Instructions could result in personal injury and/or property damage! Retain instructions for future reference. Dayton™ Marine Utility Pump Description Dayton marine utility pump is designed for general commercial and industrial applications. Unit is designed for water, but is not submersible. For use transferring liquids, emptying or filling tanks, sinks or bowls. The pump can be used to pump bilge water, but the pump must not be located in the bilge area. Self-priming to 7 ft. if the impeller is initially wet (primed). Intermittent duty. Carrying handle included. NOTE: Unit is NOT RECOMMENDED for use with soap detergents, gasoline, waste oil, fuel oil, flammable, explosive or combustible liquids or other fluids not compatible with pump component materials. Do not use unit in enclosed areas. Intermittent duty only (15 minutes per hour). Unpacking When unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. Two extra impellers and gaskets are included with pump. Specifications Power supply required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115V, 60Hz Fuse requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Amps Maximum liquid temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140°F Minimum liquid temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40°F Thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . .Automatic Resetting Motor amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.60 Amps Duty Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intermittent Dimensions Figure 1 - Dimensions E N G L I S H E S P A N O L F R A N C A I S Printed in U.S.A. 998327 Form 5S5193 05655 Rev. 01/2005 1204/399/VCPVP Dayton Operating Instructions and Parts Manual 1P579F Dayton™ Marine Utility Pump E N G L I S H Safety Guidelines WARNING Do not use to pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not use in flammable and/or explosive atmospheres. Pump should only be used with liquids compatible with pump component materials. Failure to follow this warning can result in personal injury and/or property damage. 1. Know the pump application, limitations, and potential hazards. 2. WARNING: Do not handle a pump or pump motor with wet hands or when standing on a wet or damp surface, or in water. 3. The pump is not submersible and is intended for open-air use only. 4. Disconnect power before servicing a motor or its load. If the power disconnect is outof- sight, lock it in the open position and tag it to prevent unexpected application of power. 5. Release all pressure within the system before servicing any component. 6. Drain all liquids from the system before servicing. 7. The pump motor is equipped with an automatic resetting thermal protector and may restart unexpectedly. Protector tripping is an indication of motor overloading as a result of operating the pump at low heads (low discharge restriction), excessively high or low voltage, inadequate wiring, pumping too hot a liquid, incorrect motor connections, or a defective motor or pump. Read troubleshooting chart. 8. Do not touch an operating motor. Modern motors are designed to operate at high temperatures. 9. Provide adequate protection and guarding around moving parts. 10. Secure the discharge line before starting the pump. An unsecured discharge line will whip, possibly causing personal injury and/or property damage. 11. Check hoses for weak or worn condition before each use, making certain that all connections are secure. 12. Periodically inspect pump and system components. Perform routine maintenance as required (see Maintenance section). 13. Provide a means of pressure relief for pumps whose discharge line can be shut-off or obstructed. 14. Personal Safety: Wear safety glasses at all times when working with pumps. Electrical Connections 1. Make certain that power source conforms to the requirements of your equipment. 2. When wiring an electrically driven pump, follow all electrical and safety codes, as well as the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA) in the United States. 3. This equipment is only for use on 115 volt (single-phase) and is equipped with an approved 3-conductor cord and 3-prong, grounding-type plug. 4. To reduce the risk of electric shock, the unit should be plugged directly into a properly installed and grounded 3-prong grounding-type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. The motor must be securely and adequately grounded for your protection against shock hazards! Never connect the green (or green and yellow) wire to a live terminal! 5. Wh...