Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The area in between the two is the amount of gain reduction. The unit will activate the limiter when the signal exceeds the threshold for more than 15 microseconds. Then 1 second after that the signal is below threshold again, reduction goes back to 0dB and in this case input and output signals are again identical. Peak Limiting 6ms 15ms Level Program Limiting Input Release Output approx. 1 s Threshold t/ms 10 2030 Chart. 7 SGC characteristic of the limiter section 5. INSTALLATION AND CONNECTION 5.1 Mains Connection CLE 2.0 is provided with dual voltage plug. You must check the power supply Voltage available in your Country before connecting the power cord in the wall outlet. Please see Page9, paragraph 22 for further info. 5.2 Audio connection The CLE 2.0 Compressor/Limiter/Gate is equipped with balanced XLR connectors as well as 1/4" phone jack and can be connected with other units in different ways to support a vast range of applications without experiencing a signal loss. 12 6. TECHNICAL SPECIFICATIONS AUDIO INPUT Type Active balanced XLR and 1/4"JACK Impedance Balanced: 50K Ohm Unbalanced: 25K Ohm Operating Level +4dBu /-10dBv Maximum input level alanced and nbalanced:B U +21 dBu CMRR >55dB @1KHz AUDIO OUTPUT Type XLR and 1/4" JACK Impedance Balanced: 60 Ohm Unbalanced: 30Ohm Maximum output level +21 dBu Bandwidth 20Hz to 20KHz at +0,-0.5dB THD +N% 0.01% typ.1KHz, @+4dBu 0.04% typ,1KHz, @+20dBu IMD 0.01% typ Noise >-90dBu Crosstalk <-100dB SC INPUT Type 1/4"JACK Impedance >10K Ohm Maximum input level +24dBu SC OUTPUT Type 1/4"JACK Impedance 2K Ohm Maximum output level +21dBu EXPANDER/GATE SECTION Type Interactive Expander Threshold Variable: from OFF to +15dB Ratio Variable: from 1:1.2 to 1:8 COMPRESSOR SECTION Type Interactive Compressor Threshold Variable: from -40dB to +20dB Ratio Variable: from 1:1 to :1 Manual Attack Time Variable: from 1ms to 100ms/20dB Manual Release Time Variable: from 0.05ms to 5s/20dB Auto Attack Time Typ. 15ms at 10dB; 5ms at 20 dB; 3ms at 30dB Auto Release Time Typ. 125dB/s Output Interactive Peak Limiter PEAK LIMITER SECTION Type Smart Gain Control peak limiter Threshold Variable: from +4dB to OFF Ratio :1 Stage 1: Attack and Release Clipper zero Stage 2 Attack Release Program Limiter typ. <5ms typ. 20dB/s FUNCTION SWITCHES COUPLE Linking CH1 ( master ) and CH2; stereo operation OPERATING LEVEL Internal reference level: from +4dBu to -10dBV BYPASS Bypass switch I/O METER Switches input and output for the level meter AUTO Enables the program dependent setting of the ATTACK and RELEASE times SC EXTERNAL Switches the detector section to the external SC input SC MONITOR Monitoring the external SC input, disengaging the normal audio SMART Enables the ` Smart Knee Control ` characteristics CONTOUR Allows for frequency dependent detection 15 INDICATORS GAIN REDUCTION: 12 element LED INPUT / OUTPUT LEVEL: 8 element LED EXPANDER/GATE THRESHOLD: 2 element LED ( under"+" above"-") COMPRESSOR THRESHOLD: 3 element LED ( under"+" interactive"0" above"-" ) PEAK LIMITER THRESHOLD: 1 element LED (Limiter Function ) Function switch: LED indicator for each POWER SUPPLY 95-120V /210-240V ,60-50Hz 210-240V: T200mAL 250VAC 95-120V: 400mA 250VAC FUSE: POWER CONSUMPTION 14 Watts DIMENSIONS 483(W) 194.5(D) 44(H)mm (19" 7.7" 1.7") WEIGHT 3.3kg(7.27lb) 16 7. WARRANTY 1. WARRANTY REGISTRATION CARD To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration Card within 10 days of the Purchase Date. All the information presented in this Warranty Registration Card gives the manufacturer a better understanding of the sales status, so as to purport a more effective and efficient after-sales warranty service. Please fill out all the information carefully and genuinely, miswriting or absence of this card will void your warranty service. 2. RETURN NOTICE 2.1 In case of return for any warranty service, please make sure that the product is well packed in its original shipping carton, and it can protect your unit from any other extra damage. 2.2 Please provide a copy of your sales receipt or other proof of purchase with the returned machine, and give detail information about your return address and contact telephone number. 2.3 A brief description of the defect will be appreciated. 2.4 Please prepay all the costs involved in the return shipping, handling and insurance. 3. TERMS AND CONDITIONS 3.1 LTO warrants that this product will be free from any defects in materials and/or workmanship for a period of 1 year from the purchase date if you have completed the Warranty Registration Card in time. 3.2 The warranty service is only available to the original consumer, who purchased this product directly from the retail dealer, and it can not be transferred. 3.3 During the warranty service, LTO may repair or replace this product at its own option at no charge to you for parts or for labor in accordance with the right side of this limited warranty. 3.4 This warranty does not...