Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. Always remove the plug from the mains socket before making any adjustments or maintenance, including renewing the lubricating oil. • To reduce the risk of fire or explosion, never spray flammable liquids in a confined area. It is normal for the compressor motor and pressure switch to produce sparks during use. If sparks come into contact with petrol vapours or solvents, they may ignite the vapours and cause a fire or explosion. • Always operate the compressor in a well ventilated area. Do not smoke while spraying. Do not spray where sparks or flames are present. Keep the compressor as far away from the spray area as possible. • The solvents trichloroethane and methylene chloride can chemically react with the aluminium used in some paint spray guns and form an explosion. If these solvents are used, ensure that only stainless steel spray equipment is connected. The compressor is not affected by the use of these solvents. • Never directly inhale the compressed air produced by a compressor and do not use it for charging breathing tanks. • Do not use welding equipment in close proximity to the compressor. Do not weld anything to the air tank of the compressor: this could dangerously weaken the tank and will void the warranty. • Do not use the compressor outdoors when it is raining or on a wet surface; either situation could cause an electric shock. • Always shut off the compressor after use and before servicing. Push the on/off knob down, wait for the pressurised air to bleed from the tank from the release valve and then remove the electrical plug from the power supply. • Check the maximum pressure rating of any tools or accessories that you intend using with the compressor. The output pressure of the air from the compressor must be regulated so that it never exceeds the rated pressure of the tool or accessory. • To avoid the risk of burns and injury from moving parts, do not operate the compressor with the safety cover removed. Allow hot parts to cool before handling or servicing. • Be certain to read all the labels on the containers of paint or other materials to be sprayed. Closely follow all safety instructions. Use a respirator mask if there is a chance that you might otherwise inhale the spray material. Carefully check the effectiveness of any respirator mask you intend using. • Always wear safety goggles or glasses when using the air compressor. Never point the nozzle of an accessory towards any part of your body or towards another person. • Do not attempt to adjust the pressure switch or the release valve located under the pressure switch cover. • Drain the moisture from the tank daily. It will help prevent corrosion. • Pull the ring on the safety valve daily to ensure that it operating properly and to clear any possible instructions. • Keep the compressor at least 300mm from the nearest wall to ensure adequate ventilation for cooling purposes. • Before transporting the compressor make sure that the pressurised air is bled from the tank and that the compressor is firmly secured. • Protect the air hose and cordset from damage. Inspect for weak or worn spots regularly and replace if necessary. • Do not use an extension cord with this product. Use additional air hose instead of an extension cord to prevent power loss and possible damage to the motor. Use of an extension cord voids the warranty. • After long working periods external metal parts could be hot. • Always press the on/off button down to switch off the compressor before switching off the power or removing the power plug. • Do not use the compressor without first checking the oil level. It must be close to the red circle as viewed on the oil gauge. Note. The compressor is supplied empty of oil. It must be filled with oil before first use. • After using the compressor, switch off the on/off button, disconnect the power supply and open the outlet valve to release the pressure. • Do not attempt to remove any part of the machine whilst it is under pressure. • Ensure that the lubricating oil is clean and that the oil level is maintained at the correct level. Replace the oil as indicated in the Maintenance section of this Manual. • Use safety equipment including safety goggles or shield, ear protection, breathing or respirator mask and protective clothing. Wear goggles Wear earmuffs Wear a breathing mask Never apply the outlet air of this compressor directly on to any part of a person’s body. Do not attempt to block the air outlet with your finger or any part of your body. The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury...
Dieses Handbuch ist für folgende Modelle:Pumps - EAC40 (636.43 kb)