Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Boss Audio Systems Dateigröße: 1.8 mb Dateiname: CE-3_OM.pdf Unterrichtssprache:

To prevent that, replace the battery. AC ADAPTOR (OPTION) BOSS ACA 120 ► Be sure to keep the battery securely connected even while using the AC Adaptor, then the CE-3 will continued to operate even if the AC Adaptor cord comes out during performance. * Unplug the cord from the INPUT jack when the CE-3 is not in use to avoid wasting the battery. BOSS ACA 240 BOSS ACA 220 FOR 240V AC FOR 220V AC Power................Battery 9 V ( 1), AC Adaptor (BOSS ACA series) Power Consumption......13mA at 9V Controls..............RATE knob. DEPTH knob. STEREO MODE switch Others ...............NORMAL/EF F ECT selector switch (PEDAL SWITCH). Indicator Jacks................INPUT jack. OUTPUT jacks A & B. AC Adaptor S/N Ratio.............over 90 dB (IMF A) Maximum Output Level .... OdB m (100 H?!, 10 dBm H kHz) Input Impedance ................imsj (FET Input) Output Load Impedance . . . over lOkji Dimensions........................70(W) X 55(H) x 125(D) mm/ 2-3/4(W) x 2-1 /4(H) x 5 "(D) inches Weight..............................400q/14oz * Specifications are subject to change without notice. BOSS Products of Roland Printed in Japan Jul. '87 E-3 CG-3 Chorus INSTRUCTIONS • Please read the Instructions care Adopting the stereo-out system, the BOSS effect unit CE-3 is able to produce exter-mely rich chorus sounds. By controlling the RATE and the DEPTH knobs and the STEREO MODE switch, you can obtain wide variations of the chorus sounds. Moreover, the CE-3 is designed to be noise free, i.e. the S/N ratio is more than 90 dB (IHF-A). Also, you can easily see wheather the effect is on or off by the indicator which lights up when the CE-3 is in effect mode. yAC & 0AT1 EnY '*3-4 IHl POWERED CAUTIONS FOR REPLACING AND HANDLING BATTERY REPLACING BATTERY USE 9-VOLT BATTERY. O Loosen the screw of pedal to open it and pull battery out. ©Replace the battery with a fresh one and put it into position. ©Set coil spring onto the projection on the rear of the pedal and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap in the cover or coil spring. Boscheinigung dot Mnrstnllers /Impor touts Miermit wird bescheinigt, daft der/die/das CHORUS CE 3 t yo n»pirhi in Ohereinstimmunq mil den Bestimmungen dpi Arntsbl. Vlg 1046 / 1984 tunk entstört Ist. Der Deutschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf Einhaltung der Bestimmungen eingeräumt Roland Corporation Osaka / Japan PEDAL (COVER) r THUMB SCREW SPRING BASE PEDAL GUIDE BATTERY CONNECTOR BATTERY HOUSING BATTERY STRAP 9 V BATTERY -COIL SPRING RADIO AND TELEVISION INTERFERENCE "Warning This snuiomnni hns honn ver if inri to corn ply with the limits for a Class F3 computing riovico. pursuant to Subpart J. of r*ort 1 «3 of r CC ruins Operation with non cor11fieri or non verifier* equip rnent is likely to result in interference to radio and TV reception. The equipment described in this manual generates and uses radio-frequency energy If it is not installed and used properly, that is, in strict accordance with our instructions, it may cause interfer ence with radio and television reception This equipment has been tested and found to comply with the limits for a Class B computing tfovico in accordance with the specificntiom m Suhpnrt j, of f’nr t 1 f>, of r CC Rules 1 hose mln» am designed to provide reasonable protection against such a interference in a residential installation. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can bo doterminod by turning the equipment on and off. the user is encouraged to try to correct the interference by the following measure: • Disconnect other devices and thoir input/output cablos one at n tune If the inter ferencn stops, it is caused by either the other device or its I/O cable. These devices usually require Roland designated shielded I/O cables. For Roland devices, you can obtain the proper shielded cable from your (fooler. For non Roland riovlcos, contact the manufacturer or denier for assistance. If your equipment does cause interference to radio or television reception, you can try to correct the interference by using one or more of the following measures: • Turn the TV or radio antenna ...

Herunterladen

Geben Sie zwei Ziffern: