Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Wiring diagrams for these connectors are shown below. Make connections after first checking the wiring diagrams of other equipment you intend to connect. 23 Chapter 1 Outputting Sounds Turning on the Power Chapter 1 Outputting Sounds Turning on the Power Before turning on the power, confirm the following. • Are all external devices properly connected? • Is the volume on the GT-10B, your amp, and all other connected devices turned down to the minimum level? Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. The display changes, showing the following. The screen that appears at this point is called the “Play screen.” 1. 2. Turn on the power to any external effects processors > the bass amp (power amp). The Icons in the Play Screen Master BPM OUTPUT SELECT setting Bank - Patch Number Effect Channel Category Name PREAMP Solo Sw Patch Name • Upon power-up, the patch most recently selected when the power was last turned off is selected. • This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. • The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that your unit may incorporate a newer, enhanced version of the system (e.g., includes newer sounds), so what you actually see in the display may not always match what appears in the manual. Displays the Master BPM (p. 122) value for each patch. When the Effect Ch.Mode is set to Single, effect channel A is selected. Also, this is displayed when the Effect Ch.Mode is set to Dynamic B. When the Effect Ch.Mode is set to Dynamic, the display switches between A and B according to the input level. When the Effect Ch.Mode is set to Single, effect channel B is selected. Also, this is displayed when the Effect Ch.Mode is set to Dynamic A. This is displayed when the Effect Ch.Mode is set to Dual Mix, Dual L/R, or Freq Divide. When the Effect Ch.Mode is set to Dynamic A or Dynamic B, it is displayed according to the input level. This is displayed when the PREAMP Solo Sw is Off. This is displayed when the PREAMP Solo Sw is On. For details on the OUTPUT SELECT icons, refer to “Making Settings for a Connected Device (Output Select)” (p. 26). The “S” icon is not shown if the selected amp type doesn’t have the Solo Sw parameter. 25 Chapter 1 Outputting Sounds Chapter 1 The GT-10B has a variety of Play screen variations. You can switch the information shown in the Play screen by pressing . • You can use the PARAMETER knobs 1 through 4 to work with the values of the parameters displayed at the bottom of the Play screen. Also, for each parameter, you can change the corresponding assignment at the SYS KNOB ASSIGN screen (p. 47). • The parameter name displayed at the each Play screen is abbreviated. For details about parameter names, refer to “Parameters You Can Set with PDL:CTL/EXP” (p. 125) or “Display of Parameters You Can Set with SYS KNOB SETTING” (p. 138). Switching the Play Screen Screen 1 This displays the name of the patch and the parameters you can work with using the PARAMETER 1 through 4 controls. Screen 2 This screen displays the effect channel level and the preamp that’s in use. Screen 3 This screen displays the effect channel mode and the effect channel level. Screen 4 This screen displays the functions assigned to CTL 1 and 2, the EXP PEDAL SW, and the EXP Pedal. Screen 5 This screen displays the functions assigned to the Number Pedal Switch, CTL 3 and 4, the external expression pedal (EXP PEDAL2). Screen 6 This is the screen shown when you’re in Manual mode (p. 56). Manual mode is enabled only while this screen is displayed. Pressing [CATEGORY/ENTER] in this screen allows you to make settings for MANUAL MODE SETTING. Screen 7 The effects used, as well as their connection sequence (CHAIN) in a channel is indicated. Screen 8 The patch name and the output level meter are displayed. Adjusting the Output Level 1. Adjust the GT-10B’s output level with the OUTPUT LEVEL knob. * About the S icon and A icon displayed at the Screen 4 and 5. The S icon displays when the Pedal Function is enabled (p. 48). The A icon displays when the Patch Assign Function is enabled (p. 51). Chapter 1 Outputting Sounds Making Settings for a Connected Device (Output Select) Chapter 1 Outputting Sounds Making Settings for a Connected Device (Output Select) Select the type of device connected to the OUTPUT jack. • To derive the maximum performance from the GT-10B, be sure to make the correct setting for OUTPUT SELECT, the one that’s most suitable for your setup. • The OUTPUT SELECT function affects sounds from the OUTPUT jacks. The output from the SUB OUTPUT jacks will always be equivalent to the sound that is output when the LINE/PHONES setting is used. • If the headphones ar...