Login:
Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Anleitung GE, modell JDS28

Hersteller: GE
Dateigröße: 331.08 kb
Dateiname: d771e62f-c5d2-49a9-8a32-16b76bc3c3e3.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


• IMPORTANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the consumer. • Note to Consumer – Keep these instructions for future reference. • Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under the warranty. • NOTE – This appliance must be properly grounded. • ATTENTION INSTALLER All electric drop-in ranges must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. Electric Drop-In Range Installation Instructions JDS28, JDP39 MATERIALS NEEDED Junction Box Wire NutsStrain Relief Clamp for 1/2” conduit PARTS INCLUDED Lower Trim 2 Screws 2 Shoulder Screws (for stop device) TOOLS YOU WILL NEED 1/8” Drill Bit and Electric or Hand Drill Phillips Screwdriver Nut Driver Level Tape Measure Straight Edge or Square Hand or Sabre Saw Standard Screwdriver Pencil Safety Glasses Hammer Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com PARTS INCLUDED Lower Trim 2 Screws 2 Shoulder Screws (for stop device) TOOLS YOU WILL NEED 1/8” Drill Bit and Electric or Hand Drill Phillips Screwdriver Nut Driver Level Tape Measure Straight Edge or Square Hand or Sabre Saw Standard Screwdriver Pencil Safety Glasses Hammer Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com 31-10595-2 1-07 JR 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING: For personal safety, remove house fuse or open circuit breaker before beginning installation. Failure to do so could result in serious injury or death. • All rough-in and spacing dimensions must be met for safe use of your range. • To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that protrudes at least 5” beyond the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 13”. • Be sure your appliance is properly installed and grounded by a qualified technician. ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located behind the oven door on the range.) Rating plate location We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician. After installation, have the electrician show you where your main range disconnect is located. Check with your local utilities for electrical codes which apply in your area. Failure to wire your range according to governing codes could result in a hazardous condition. If there are no local codes, your range must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70— Latest Edition. You can get a copy by writing: National Fire Protection Association Batterymarch Park Quincy, MA 02269 Effective January 1, 1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric range. When installing an electric range in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION. You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used. 2 Installation Instructions PRE-INSTALLATION CHECKLIST • Move Range Indoors In Front of Cabinet Door removal is not a requirement for Opening installation of the product, but is an added convenience. To remove the door: • Protect the kitchen floor! Flatten and place a piece of the shipping carton in front of the • Open the oven door as far as it will go. installation location to protect the flooring. • Inspect Installation Location Inspect cutout dimensions and location of electrical junction box to be sure it fits within the layout location. See page 4. Refer to alternate construction section for the following non-standard installations. a. Counter opening extends to the wall: Maintop Filler Kit (JXS66XX), or Backguard Kit (JXS32XX). WARNING: If you do not use these kits, the anti-tip bracket must fit under an attachment to the wall that can withstand a force of 200 lbs. in the upward direction. See Step 1 under INSTALL THE RANGE. b. Island Installation: To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make th...

Dieses Handbuch ist für folgende Modelle:
Musikinstrumente - 131-10595-2 1-07 JR (331.08 kb)
Musikinstrumente - JDP39 (331.08 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien