Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
In order to make the most of the advanced features and performance provided by your guitar, please read this manual carefully before using the instrument. PRECAUTIONS The output jack is an EIAJ-standard 1/4" phone jack. Be sure to use an appropriate connection cable. The built-in preamplifier is automatically turned on when a plug is inserted into the output jack. When not using the instrument, or when playing it without amplification, be sure to remove the plug from the output jack so that the preamplifier power is turned off. Always set the VOLUME control to “0” when plugging in or unplugging the connection cable. The battery check indicator (BAT.) will light briefly when a plug is inserted or removed from the output jack. This is normal and does not indicate a malfunction. Be sure to remove the battery if the instrument will not be used for an extended period of time in order to prevent possible damage due to battery leakage. BATTERY REPLACEMENT SPECIFICATIONS System SYSTEM-42 (1 way) SYSTEM-43 (2 way) Pickup Electret Film Type EMF : B-Band22L EMF : B-Band22L Omni Directional Condenser Mic — YAMAHA : MC-7 Pre-amplifier Controls HIGH, LOW, VOLUME HIGH, LOW, VOLUME MIC. (Phase Adjust) Output jack Combination end pin/power switch Output impedance 10 k.Power supply 9V DC, S-006P (6F22) dry cell battery Battery life (continuous use) Approx. 340 hours Approx. 150 hours Power consumption Approx. 1.7 mA Approx. 3.8 mA Model CGX-111SC CGX-171CC Be sure to replace the battery as soon as possible when the battery check indicator lights in order to avoid reduced sound quality. * Be sure to remove the battery if the instrument will not be used for an extended period of time in order to prevent possible damage due to battery leakage. q Press the catch on the battery holder in w Slide out the battery case. the direction indicated by the arrow in the illustration in order to unlock it. Battery case OPEN OPEN Catch e Remove the old battery from the battery r Slide the battery case back case, and insert the new battery making into the battery holder and sure that the (+) and (–) terminals of the press firmly so that the battery are positioned as shown in the battery case locks into illustration. Use only a DC9V, S-006P place. (6F22) or equivalent battery. DC9V S-006P (6F22) NOMENCLATURE Battery HolderControl Section Output Jack (with power switch function) Pickup Electret Film Type Pickup Condenser Mic (System 43 only) THE CONTROLS . System 42 (1 way) e qw64 20 HIGHBATT. VOL. 810 12100 1264 2 0 LOW 12 68 10 2 4 8 q Volume Control This knob controls the volume. w BATT. (Battery Check) Lamp When battery power is low the lamp will light. Please replace the battery with a new set as soon as possible. (Refer to “BATTERY REPLACEMENT" section.) e Equalizer Controls When both the HIGH and LOW knobs are set to "0", the signal will be flat (EQ Pass). HIGH :Rotate the knob to the right to enhance the high frequencies and create a brighter sound. LOW :Rotate the knob to the right to enhance the low frequencies and add presence. . System 43 (2 way) r64 20 HIGH BATT. MIC. VOL. Reverse 812100 12NormalOFF 42464 2 0 LOW 8 10 12 4 62 8w q e r Mic (Phase Adjustment) * System 43 only When the mic knob is set to its center position, the mic is off. Rotate the knob to the right (Normal) to increase the mic mix level. At this time, if feedback or howling occurs, it is possible to reverse the phase by rotating the knob to the left. The same knob provides control of both level and phase adjustment. Caution Rotating the HIGH and LOW knobs to the right increases the overall output level. Likewise, rotating the MIC. knob right or left also increases the overall output level. If the overall output level is increased in this manner, use the VOL. knob to adjust the volume level. CONDENSER MIC ADJUSTMENT (System 43 only) The condenser mic is attached inside the body (behind the preamplifier) with a flexible pipe that allows free adjustment of the mic's direction. A variety of tone variations are achievable by changing the direction of the mic head. • When the guitar was shipped from the factory, the mic head is positioned inside the body slightly pointed towards the sound hole and about 10mm from the guitar's top. (You can see it from the sound hole.) This setting is good for picking up the sound of the strings being plucked. (See diagram 1) • When the mic head is slightly pointing toward the inside of the body this setting will pickup a bigger body sound. (See diagram 2) *Try some different mic placements and select the one you prefer. (Diagram 1) Toward the center of the body Mic Head Strings 10 mm (Diagram 2) ...