Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If the device is not proper, pull out the plug at once and contact your retailer or the nearest distributor. »¿№9 iM* a ««t* »(H ii ;l 'afei 1. Handle 2. Power switch and master volume control 3. Compartment door for cassette 4. Volume control for wired mic 5. Repeat touch-tone board 6. Power indicator 7. Low battery indicator 8. Chatging indicator 9. Tape volume control 10. Echo control 11. Treble control 12. Bass control 13. AC power fuse socket 14. Voltage selector switch 15. 2PINjack 16. DC input jack 17 Rechargeable batteiy compartment 18. Antenna 19. Volume control A for wireless mic 20. Treble speaker 21. Speaker frame 22. Bass speaker 23. Volume contr ol B for wireless mic 24. Wireless audio signal indicator 25. Wireless RF indicator Figure A —u Figure B 26. Mic jack 27. Output jack, coiuiect speaker 28. Input jack, coimect audio sau ce 29. Earphone output jack 30. Power switch for transmitter 31. Signal indicator for transmitter 32. Volume control for transmitter 33. Wireless bodypack transmitter 34. Tie-clip inic 35 Handlield mic head 36. Handheld mic battery condition indicator 37 Handlield mic switch 38. Battay housing 39. Headset mic Figure C 38 39 -3— !,1MSXRI!CJI0NS 1. Confirm the power: A. When use the AC power: 1) Please confirm if your currently AC power as same as the device parameter. if no. the device will be destroyed. 2) Tuni on the volume control in clockwise direction, tins device is normal working when the panel red power LED is come on. 3) Open the batteiy cover of the transmitter, put a 9V battery into it, then close. Put the plug of headset into the inic jack on the transmitter, keep the distance as 0.8-1M between the mic head and receiver, switch ON die transmitter, the red indicator light will flash once, the wireless device start working. Time the master volume control and wireless mic volume control to your desired volume. B. When use the build-in DC 12V rechargeable batteiy: 1) Insert the rechargeable batteiy in correct polarity direction.(DC 12V: Red means +, Black means -.) 2) Turn on the power/master volume control in clockwise direction. Red indicator is come on, this device is working now. If the low battei y indicator is come on to yellow means the voltage is not enough, please rechaige it. C When use the outer DC 12V rechargeable battei y: Outer DC power can be input into by DC jack directly. When use car batteiy: voltage should be 12V -15V, please note the coirect polarity. D. When recharging: 1) Plug the power cable into AC jack for recharging, when RECHARGE indicator turn to GREEN from YELLOW, means voltage is enough. 2) Please recharge the batteiy every 2 months if you don't use it for a long time, and rechaige it S -10 hours continuous. „4.. N STRUCT IONS ) 2. General operation : 1) Normal play.Tum 011 the power/master volume control in clockwise direction, Press the STOP/EJECT key on the cassette, open the compartment to put into the tape, then press PLAY, adjust the power / m-aster volume control knob. Also adjust the tone control, tape volume control, Echo contr ol to get the best sound effects. 2) Wired microphone and Karaoke function: Plug the wired microphone into the MIC jack, let it far away the main unit if possible (avoid the feedback noise). Then getting the perfect amplifying effects if adjusting the master volume control and Tone control, and assort with the accompanying tape music, so realize the Karaoke function. 3) Amplify the outside Audio (CD. VCD etc): Connect the outside audio source with the input jack, adjust the master volume and tone control knobs, they can amplify the outside signal. 4) Cassette record. Open the cassette compartment, put into a vacant tape, press the EEC key and PLAY key simultaneously to realize the recording function from wire/wireless microphones signal and outside audio source. 3. Wireless microphone: 1) Insert a 9V batten' for the wireless bodypack transmitter, push the power switch to middle position, then the power indicator light will flash once. Turn on power of the main unit, draw out the antenna. Now the wireless receiver RF light of the main unit will shine, speaker is quiet. 2) Push the transmitter switch to ON, then you can listen the speaking sounds, adjust master volume control and tone control knobs, to a suitable position in order to avoid the noise even the rotund sounds from speaker. The signal level indicator show you the signal is big or small. 3) When the transmitter power switch is ON, and the power indicator is lighting all along, means that the transmitter battery is not enough, please replace it. -V- [INSTRUCTIONS 4. Computer repeat:(This device belongs to the Hifi original speaker repeat, repeat time:200 seconds) 1) Play the tape, if you want to replay foregoing sounds, just press the REPEAT key. Then the tape will be stopped at this moment, then start to repeat. And you can listen it 200 seconds again and again. 2) If...